KOREPOX H.B EH3200 Epoxy Glass Flake Paint belongs to glass flake paints, epoxy system. Parameters on this page: volume solids approx. 100% (measured to ISO 3233), DFT 1000 µm (single coat), theoretical spreading rate 10.0 m²/L/100 µm. Comparable models from the same brand: KOREPOX H.B EH3200 Epoxy Glass Flake Paint, Korepox EH2350 Epoxy Glass Flake Paint, KOREPOX EH2350 High-build Epoxy Primer.
Parameter source: original KCC technical data sheet (TDS) "KOREPOX H.B EH3200(GF) Epoxy Glass Flake Paint"; values such as spreading rate are converted from TDS parameters and serve as selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | Approx. 100% |
|---|---|
| Dry Film Thickness | 1000 µm (single coat) |
| Theoretical Spreading Rate | 10.0 m²/L /100 µm |
| VOC | — |
| Density / Specific Gravity | 1.20–1.40 kg/L (after mixing) |
| Number of Components | Two-component |
| Colour / Appearance | Semi-gloss, grey (GREY) |
| Packaging Specifications | 16L pack (EH3200(GF)-A: 12.8L, EH3200(GF… |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
KOREPOX H.B EH3200(GF) is a coating based on epoxy resin reinforced with glass flake, offering excellent water resistance and abrasion resistance, long-term durability and a firm film. The product is self-priming and can be applied to form a thick film; as a solvent-free product it complies with VOC regulations.
Used as primer or topcoat on surfaces requiring good abrasion resistance and corrosion resistance, such as marine structures, piping and exposed steel structures.
| Appearance and colour | Semi-gloss, grey (GREY) |
|---|---|
| density | Approx. 1.20–1.40 after mixing |
| Volume Solids | Approx. 100% (measured to ISO 3233) |
| Theoretical Spreading Rate | 1.0 m²/L at 1,000 µm DFT on a smooth surface |
| Flash Point | Base (EH3200(GF)-A): 45°C (closed cup); Hardener (EH3200(GF)-B): 39°C (closed cup) |
Before application, remove all oil, grease, dust and other contaminants from the surface to be coated by suitable methods such as solvent cleaning and fresh water washing. * Steel: blast clean to a minimum of Sa2.5 for both immersed and non-immersed areas. * Concrete: blast clean or acid etch to remove all previous coatings, powdery matter and glaze or laitance on the surface.
Airless spray or brush application (narrow areas). ● Airless spray: nozzle orifice 483-782 µm (0.019-0.031″); spray pressure 26-43 MPa; spray angle 65°. ● The compression ratio of the application equipment shall be greater than 66:1. ● Immediately after use, clean the application equipment thoroughly with Thinner No.024.
Base (EH3200(GF)-A) : Hardener (EH3200(GF)-B) = 4:1 (by volume). Mix thoroughly in the indicated ratio before application.
No thinning required (if necessary, Thinner No.024 up to 5% by volume). Do not thin the two components separately; the mixture shall be thinned.
● The substrate shall be clean and dry; application and curing temperature 10-40°C; relative humidity below 85%. ● Substrate surface temperature shall be at least 3°C above dew point. ● In winter, maintain substrate and ambient temperature above 10°C and curing temperature above 5°C after application. ● In confined spaces, provide adequate ventilation during application.
Single coat: DFT 1,000 µm. Film thickness varies with application area and use; drying time, recoat interval and spreading rate will also change.
| Substrate Temperature | 10°C | 20°C | 30°C |
|---|---|---|---|
| Touch dry | 18 h | 10 h | 8 h |
| Curing/drying | 72 h | 48 h | 36 h |
In accordance with the coating specification.
1 h at 20°C/68°F.
At 20°C, minimum 36 h, maximum 7 days. If the maximum recoat interval is exceeded, roughen the surface before application.
Continuous: 93 °C (non-settling); intermittent: 121 °C (non-settling).
| Shelf life | 12 months |
|---|---|
| Packaging Specifications | 16L pack (EH3200(GF)-A: 12.8L, EH3200(GF)-B: 3.2L) |
● Provide adequate ventilation during application. ● In confined spaces, wear respiratory protection. ● Store away from moisture and direct sunlight. Issue date: 2010-06-01; revision date: 2015-09-01.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
