KOREPOX EH2350 Epoxy Primer is an epoxy paint, used as a primer. Parameters on this page: volume solids approx. 80% (determined per ISO 3233), dry film thickness 125 µm (single coat), theoretical spreading rate 8.0 m²/L/100 µm. Comparable products of the same brand: KOREPOX EH2350 High-build Epoxy Primer, KOREPOX EH2350 Epoxy Primer, Korepox Holding Primer EP1700 Epoxy Primer.
Data source: KCC original Technical Data Sheet (TDS), "KOREPOX EH2350 Epoxy Primer"; spreading rate and other values are converted from the TDS parameters, for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | Approx. 80% |
|---|---|
| Dry Film Thickness | 125 µm (single application) |
| Theoretical Spreading Rate | 8.0 m²/L at 100 µm |
| VOC | — |
| Density / Specific Gravity | 1.5 kg/L (after mixing, depending on colour) |
| Number of Components | Two-component |
| Thinner | 024 |
| Colour / Appearance | Flat, grey (1128, 1151) |
| Packaging Specifications | 16 L package (EH2350PTA: 12.8 L, EH2350PTB: 3.… |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Korepox EH2350 is a two-component functional primer paint with epoxy resin as the main component, with excellent salt water resistance and abrasion resistance. This product can be applied not only to new substrates but also to old films — as long as the raised rust on corroded substrates is removed, application can proceed. This product can be applied and cured at low temperatures (down to -18 °C), and as a tar-free high-solids paint it complies with VOC regulations. Lloyd's Register (LR) and Germanischer Lloyd (GL) approve this product as a corrosion control coating for ballast water tanks; the Newcastle Occupational Health Agency approves this product as a coating for grain-carrying ship holds; and it has obtained CE marking from Det Norske Veritas (DNV).
A self-priming, abrasion-resistant paint for steel structures such as seawater tanks, ship outer plates, exposed areas and warehouses that require long-term protection in severely corrosive marine environments.
| Appearance and colour | Flat, grey (1128, 1151) |
|---|---|
| density | Mixture, approx. 1.5 depending on colour |
| Volume Solids | Approx. 80% (measured according to ISO 3233) |
| Theoretical Spreading Rate | On a smooth surface, dry film thickness 125 µm, 6.40 m²/L |
| Flash Point | Base (EH2350PTA): 26 °C (closed cup); hardener (EH2350PTB): 26 °C (closed cup) |
Remove rust, dust, moisture, oil and other contaminants from the substrate surface completely with clean water or a suitable solvent. • Iron substrates: blast clean to at least Sa 2.5, or power tool cleaning to St 3 may be used.
KOREPOX EH2350, GALVANY shop primer IZ182(J), or according to the coating specification.
Airless spray or brush application (for narrow areas). Airless spray: nozzle tip size 483–787 µm (0.019–0.031 in); spray pressure 11.7–15.2 MPa; spray angle 40–60°.
Base (EH2350PTA) : Hardener (EH2350PTB) = 4 : 1 (by volume). Mix the two components completely in the specified ratio before application.
Thinner 024. Do not thin the two components separately; the mixture must be thinned.
The surface must be clean and dry, and the relative humidity must be below 85%. The substrate surface temperature shall be above the dew point by 3 °C. When applying in winter, keep the substrate and air temperature above 10 °C, and keep the curing temperature above 5 °C after application.
Single application: dry film thickness 125 µm. The film thickness may be adjusted according to the coated area and purpose.
| Classification | 5°C | 20°C | 30°C |
|---|---|---|---|
| Touch dry | 8 h | 1 h | 30 min |
| Curing/drying | 16 h | 3 h | |
In accordance with the coating specification.
At 20 °C, 3 h.
At 20 °C, minimum 3 hours; maximum: none (non-immersed epoxy coating systems), 10 days (immersed epoxy coating systems).
Continuous: 93 °C (non-deposition conditions); intermittent: 121 °C (non-deposition conditions).
| Shelf life | 12 months |
|---|---|
| Packaging Specifications | 16 L package (EH2350PTA: 12.8 L, EH2350PTB: 3.2 L) |
Must be stored at 5 °C–40 °C. Prevent this product from contacting skin and eyes; avoid prolonged inhalation of solvent vapours. Ensure adequate ventilation during application; wear respiratory protective equipment when working in enclosed spaces. Date of issue: 2010-06-01.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
