6182H CMP NOVA 5000 BARRIER Solvent-free Epoxy Mastic belongs to Epoxy. CMP NOVA 5000 BARRIER is a solvent-free epoxy mastic, qualified in accordance with MSC.1/Cric.1300 and MSC.1/Cric.1399 for use as a protective coating in ballast tanks and cargo oil tanks. Parameters on this page: volume solids 100%, dry film thickness 300 µm, theoretical spreading rate 0.3 L/m2. Comparable models from the same brand: 5006 ALP 500 Epoxy, 5055 BANNOH 500 Epoxy, 5055D BANNOH 500 AC Epoxy.
Parameter source: CMP original technical data sheet (TDS) "6182H CMP NOVA 5000 BARRIER Solvent-free Epoxy Mastic"; values such as spreading rate are converted from TDS parameters and are for model selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 100% |
|---|---|
| Dry Film Thickness | 300 µm |
| Theoretical Spreading Rate | 0.3 L/m2 |
| VOC | 195 g/L |
| Density / Specific Gravity | 2.16 g/mL |
| Number of Components | Two-component |
| Thinner | EPOXY THINNER (for cleaning only) |
| Mixing Ratio | Base : curing agent = 55:45 (by volume) |
| Colour / Appearance | Grey |
CMP NOVA 5000 BARRIER is a solvent-free epoxy mastic, qualified in accordance with MSC.1/Cric.1300 and MSC.1/Cric.1399 for use as a protective coating in ballast tanks and cargo oil tanks. It provides good seawater resistance and high crude oil resistance; it also has excellent adhesion and bonds to simply prepared and/or slightly damp surfaces.
| Type | Solvent-free epoxy mastic |
|---|---|
| Use | Suitable for ballast tanks, void spaces and similar spaces. |
| Mixing Ratio | Base : curing agent = 55:45 (by volume) |
|---|---|
| Colour | Grey |
| Flash Point | Base >=250 °C Hardener 155 °C |
| Density | 2.16 g/mL |
| Volume Solids | 100% |
| Volatile organic compound content | 195 g/L |
| Theoretical spreading rate | 0.3 L/m2 |
| Thickness | WFT 300 µm |
| Dry film | 300 µm |
(DFT 300 µm)
| Temperature | 5 °C | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 48 h | 8 h | 4 h | 2 h |
| Hard Dry | 72 h | 24 h | 12 h | 8 h | |
| Recoat interval | At least | 72 h | 24 h | 12 h | 8 h |
| At most | 7 days | 7 days | |||
| Pot life | 1.5 h | 1 h | 40 min | 30 min | |
| Minimum launching time | 60 h | 18 h | 8 h | 6 h | |
| Application method | Brush, roller, knife, trowel, hand application |
|---|---|
| Weather: temperature | Minimum 5 °C |
| Humidity | Maximum 85% RH |
| Thinner | EPOXY THINNER (for cleaning only) |
| Thinning | None recommended |
High-pressure water jet (pressure above 15000 psi recommended) or power tools to Sa2
| (ISO 8501-1 | 2007) to clean the damaged areas. Remove salt and other contaminants. |
|---|
CMP NOVA 5000 BARRIER may be applied to undried surfaces.
| Preceding coat | - |
|---|---|
| Subsequent coat | - |
| Packaging | Two-component |
Note: 1. Stir the base with a stirrer until uniform, then add the curing agent and mix with the base using a powerful stirrer. Then add an appropriate amount of thinner and mix.
2 Store the paint in a cool place to ensure the paint is at a suitable temperature. The temperature rise caused by mixing large quantities of paint shortens the pot life.
3 If the coating surface is exposed to direct sunlight, apply the subsequent coat as soon as possible after the minimum overcoating interval.
4 Density, volume solids and VOC content are theoretical values calculated without thinner.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
