PPG SIGMADUR ONE One-component Polyurethane Topcoat

Browse Similar Models by CategoryThis model belongs to: Topcoat, Polyurethane

Key properties

• Easy to apply on freeboard, deck and superstructure.
• The film-forming resin is pre-reacted and no isocyanate needs to be added for curing.
• Easy to use
• Excellent levelling
• Recommended application methods are brush and roller
• Fast drying
• May be overcoated on most old coatings, such as alkyd, chlorinated rubber and epoxy, provided the old coating is sound and firmly adhered, ensuring good intercoat adhesion.
• High gloss
• Good colour and gloss retention

Colour and gloss

• White and other colours (refer to the company standard colour chart, SIGMACARE shade card)
• Gloss

Basic data at 20 °C (68 °F)

Product parameters

Maximum 400.0 g/L (approx. 3.3 lb/gal) (theoretical calculated value)

Substrate condition

• Previous coats (alkyd, epoxy or polyurethane) must be clean and dry, with all contaminants removed.
• Previous coat: if necessary, abrade thoroughly before coating

Substrate temperature and application conditions

• During application, the substrate temperature must not exceed 50 °C (122 °F)
• During application, the substrate surface temperature must be maintained at least 3 °C (5 °F) above the dew point.

Coating system specification

• Coating system for superstructures and deck outfitting — system sheet SYSTEM SHEET 3104

Instructions for use

• Stir thoroughly before use
• The paint temperature should be controlled above 15 °C (59 °F)
• During application and curing, ensure continuous, adequate ventilation (see sheets {1433} and {1434})

Brush/roller

Supplementary parameters

Recoating interval schedule for a dry film thickness of 70 µm (2.8 mils)

Safety Precautions

• For the coating and its recommended thinners, see Safety Sheets 1430 and 1431 and the relevant Material Safety Data Sheet
• This is a solvent-borne coating. Avoid inhaling spray mist and solvent vapours, and avoid contact of uncured paint with skin and eyes.

Worldwide

Although PPG Protective and Marine Coatings is committed to providing completely consistent products to users worldwide, from time to time it may be necessary to make minor adjustments to specific products to comply with local/national regulations or environmental requirements. In the following cases, use the corresponding alternative version of the product data sheet instead.

Reference information

• For product data, refer to Information Sheet 1411
• For safety guidance, refer to Information Sheet 1430
• Safety and health in confined spaces | explosion hazard — toxic hazard: refer to Information Sheet 1431
• For safe working in confined spaces, refer to Information Sheet 1433
• For ventilation guidance, refer to Information Sheet 1434

Quality guarantee

PPG warrants (1) that it has good title to the product, (2) that the product quality conforms to the relevant technical quality specifications in force at the date of manufacture of the product, and (3) that the supplied product is free of lawful claims by third parties for infringement of US patent rights. The above warranties are limited to those given by PPG and other express or implied warranties required by applicable laws and regulations for transactions and commercial practice; any abuse contrary to the stated conditions, and any other warranty for special purposes or uses, are excluded, and PPG shall be free from liability. To claim under this warranty, the buyer must notify PPG in writing within five (5) days of discovering the quality defect, and the date must be within the product's valid storage period or within one (1) year from delivery of the product to the buyer. If the buyer fails to notify PPG of the defect as required above, this will prejudice the buyer's right to obtain compensation under this warranty from PPG!

Limitation of liability

In all cases, PPG shall not be liable for any indirect, special, incidental or consequential loss of any kind arising from or in connection with the use of this product (whether based on negligence, strict liability or tort).

The information in this product data sheet is based on laboratory tests we believe to be reliable, and is provided for guidance only.

PPG may revise this information at any time as experience accumulates and product development progresses.

All recommendations and advice concerning the use of this product, whether in technical documents, in response to an enquiry or otherwise, are given to the best of our knowledge and are believed to be reliable.

Our products and related information are provided for industrial users possessing the necessary knowledge and practical skills, and it is the end user's responsibility to determine whether the product is suitable for the specific use. The buyer, having performed such evaluation, proceeds entirely at its own risk. The quality and condition of the substrate on site, and the many other factors affecting product use and application, are beyond PPG's control. Therefore, PPG accepts no liability for any loss, injury or damage arising from the use of the information in this product data sheet (unless otherwise provided in a written agreement). Different application environments, changes to the application process or extrapolation of the reference data may result in failure to achieve the expected coating quality.

This product data sheet supersedes all previous versions. The buyer is responsible for confirming that the data sheet in hand is the latest version before using the product. The latest version is published on the official website of PPG Protective & Marine Coatings: www.ppgpmc.com. In case of discrepancy between the Chinese version and the original English version of the product data sheet, the English original shall prevail.

The PPG Logo, Bringing innovation to the surface., and other PPG marks are property of the PPG group of companies. All other third-party marks are property of their respective owners.