Baltoflake Glass Flake Polyester is a glass flake coating. At application temperatures above 25 °C, Baltoflake FC is recommended for single-coat application, or as the topcoat in a two-coat system of one coat of Baltoflake and one coat of Baltoflake FC. It is an ultra-high-build protective coating featuring excellent abrasion resistance and fast curing. Parameters on this page: volume solids 96 ± 2%, dry film thickness 600–1500 µm, theoretical spreading rate 1.5–0.6 m²/L. Comparable products from the same brand: Baltoflake FC Glass Flake Polyester FC, Baltoflake S2000 Glass Flake Polyester S2000, Jotacote Xtend GF Ultra-high-solids Abrasion-resistant Epoxy Glass Flake.
Source: JOTUN original technical data sheet (TDS) "Baltoflake Glass Flake Polyester"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 96 ± 2% |
|---|---|
| Dry Film Thickness | 600–1500 µm |
| Theoretical Spreading Rate | 1.5–0.6 m²/L |
| VOC | 80 g/L |
| Density / Specific Gravity | 1.2 kg/L |
| Number of Components | Two-component |
| Flash Point | 34 °C |
| Thinner | Styrene |
| Gloss | Matt (0–35) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Glass Flake Polyester (0BT)
A glass-flake-reinforced unsaturated polyester coating. An ultra-high-build protective coating featuring excellent abrasion resistance and fast curing. Can be used as a primer, intermediate coat or topcoat in atmospheric and immersed environments. Suitable for suitably prepared carbon steel, stainless steel, aluminium and approved primers
Recommended for areas subject to frequent mechanical abrasion and severe service environments. Recommended for offshore environments, including splash zones, breakwaters, piles, tidal zones, decks, battery rooms, power stations, exteriors of buried tanks, concrete embankments, refineries, bridges, mining equipment and general structural steel that is difficult to maintain.
When the application temperature is above 25 °C, Baltoflake FC is recommended for a single coat, or as the topcoat in a two-coat system of one coat of Baltoflake and one coat of Baltoflake FC.
Others
APAS certified to standards 2917, 2917F, 2917P and 2917S. NORSOK Standard M-501, 6th edition, Coating System No. 1 — carbon steel with maximum operating temperature <120 °C. NORSOK Standard M-501, 6th edition, Coating System No. 4 — walkways, escape routes and storage areas. NORSOK Standard M-501, 6th edition, Coating System No. 7A — carbon steel or stainless steel in the splash zone. Other certificates and approvals are available on request.
Baltoflake FC Glass Flake Polyester FC (0R6)
For the different products in this series, refer to the respective technical data sheets
Many other colours are available
| Property | Test / Standard | Description |
| Volume Solids | Theoretical Value | 96± 2 % |
| Gloss (GU 60°) | ISO 2813 | Matt (0–35) |
| Flash Point | ISO 3679 Method 1 | 34 °C |
| Density | Theoretical Value | 1.2 kg/L |
| VOC — USA / Hong Kong | US EPA Method 24 (test value) (CARB (SCM) 2007, SCAQMD Rule 1113, Hong Kong) | 80 g/L |
| VOC — EU | IED (2010/75/EU) (theoretical value) | 4 g/L |
| VOC — China | GB/T 23985-2009 (tested) | 80 g/L |
The data listed are based on factory batch production and may vary slightly with colour.
| Gloss description | According to JOTUN's definition of functional coatings |
|---|
Typical recommended specification range
| Dry Film Thickness | 600–1500 µm |
| Wet Film Thickness | 650–1650 µm |
| Theoretical Spreading Rate | 1.5–0.6 m²/L |
All vinyl ester and polyester coatings may shrink during curing. This makes the practical spreading rate lower than the theoretical. The shrinkage depends on the actual dry film thickness and application conditions.
To ensure lasting adhesion of the next coat, all surfaces must be clean, dry and free of contaminants.
Surface Preparation
| Substrate | Minimum | Recommended |
| Carbon Steel | Sa 2½ (ISO 8501-1); surface roughness medium to coarse G (ISO 8503-2) | |
| Aluminium | Cleanliness and surface roughness per Sa 2½ (ISO 8501-1) and medium to coarse G (ISO 8503-2) respectively | |
| Stainless steel | Cleanliness to Sa2½ (ISO 8501-1), surface rough | Cleanliness and surface profile to Sa2½, medium to rough |
| fine to medium G (ISO 8503-2). | G(ISO 8503-2) | |
| Coated surface | A clean, dry and sound compatible primer. | |
This product may be applied by the following methods
| Spray | Standard airless spray may be used. Dedicated two-component airless spray is optional. |
|---|
The substrate temperature must not be below the paint temperature, nor more than 20 °C above it.
Additive addition per 16 L of product (ml).
Due to differing regional regulations, packaging sizes and fill capacities may vary by region. Adjust the quantity of additive accordingly.
Paint temperature
| Additives | 10-14 °C | 15-19 °C | 20-24 °C | 25-29 °C | 30-34 °C | 35-40 °C |
| JOTUN Accelerator CO1P or Accelerator 9802 P | 300 | |||||
| JOTUN Peroxide No. 1, Norox KP-9 or Butanox M-50 | 300 | 200 | 200 | |||
| JOTUN Inhibitor No. 51 | 200 | 400 |
Consult JOTUN for further additive suppliers.
| Warning | The accelerator must never come into direct contact with peroxides. |
|---|
All peroxides must be stored in a dark, cool environment (below 25 °C), away from all flammable materials. Do not expose to direct sunlight. Use only original or approved containers.
Empty containers should be rinsed with water and stored separately.
Peroxides ignite if exposed to sparks and hot metal dust from grinding or other mechanical work.
The curing reaction generates heat. Fill containers of surplus mixed paint with water to avoid excessive heat build-up.
| Thinner: | Styrene |
| Maximum thinning: | 5 % |
| Cleaner: | JOTUN Thinner No. 17 / JOTUN Thinner No. 27 |
| Nozzle tip size (inch/1000): | 27-35 |
| Nozzle pressure (minimum): | 150 bar/2100 psi |
| Substrate Temperature | 10 °C | 23 °C | 40 °C |
| Touch Dry | 3 h | 2 h | |
| Walk-on Dry | 5 h | 2 h | |
| Minimum recoat interval | 5 h | 2 h | |
| Dry/cured to service | 4 days | 2 days | 1 day |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
Drying and curing times are determined based on temperature and relative humidity below 85%, with dry film thickness within the average range.
For the touch-up procedure of small areas, refer to the repair of the coating system.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|---|
| Walk-on Dry | The minimum time after which the coating allows normal foot traffic without leaving permanent footprints, marks or other physical damage. |
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
Dry/cured to service: the minimum time before the coating can be permanently exposed to a specific environment/medium.
| Paint temperature | 23 °C |
| Pot Life | 45 min |
Temperature
| Drying, atmospheric | Continuous 90 °C | Peak 100 °C |
| Immersed, sea water | 50 °C | - |
Withstands peak temperatures for a maximum of one hour.
At the above temperatures, protective performance is unaffected, but appearance may be affected.
Note: this coating can withstand different immersion temperatures, depending on the specific chemical and whether immersion is continuous or intermittent. Heat resistance is affected by the coating system as a whole. When used with other coatings, ensure that all coatings in the system have similar heat resistance.
| Previous coat: | Unsaturated polyester, unsaturated vinyl ester |
| Subsequent coat: | Unsaturated polyester, polyurethane, polysiloxane |
| Volume | Container Size | |
| (L) | ||
| Glass Flake Polyester | 16 | 20 |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
Storage temperature not exceeding 25 °C.
Glass Flake Polyester 6 months
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge. Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling, products may show slight colour variation from batch to batch. Likewise, fading and chalking may occur when exposed to sunlight.
Gloss and colour retention of topcoats depend on the colour type, the surrounding environment such as temperature and UV intensity, and application quality.
Contact your local JOTUN office for further information.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
