It also has good application properties as well as excellent adhesion and weather resistance. Parameters on this page: volume solids 100%, number of components: one-component. Comparable models from the same brand: 8440 BITUMEN SOLUTION B bituminous paint, 3007 SILVAX SQ-K vinyl resin primer, 4008 CMP AC special synthetic resin anticorrosive paint.
Parameter source: CMP original technical data sheet (TDS) for 2330B NON-SKID DECK SAND Anti-Skid Additive (Anti-Skid Sand); spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 100% |
|---|---|
| Dry Film Thickness | — |
| Theoretical Spreading Rate | — |
| VOC | 0 g/L |
| Density / Specific Gravity | — |
| Number of Components | One-component |
| Drying Time | Surface Dry |
| Recoat Interval | At least |
| Composition/type | Non-skid additive (non-skid grit) |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
NON-SKID DECK SAND provides a good anti-skid surface.
It also has good application properties as well as excellent adhesion and weather resistance.
| Type | Non-skid additive (non-skid grit) |
|---|---|
| Use | Applied in areas with anti-skid requirements such as deck walkways |
Colour:
| Flash Point | - [°C ] |
|---|---|
| Volume Solids | 100% |
| Volatile organic compound content | 0 g/L |
| Theoretical spreading rate | L/m2 |
Thickness:
| Temperature | 5 °C | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | - | - | ||
| Hard Dry | - | - | |||
| Recoat interval | At least | - | - | ||
| At most | - | - |
Application method: Method A;
1. Apply the recommended coating by airless spray, brush or roller. 2. Sprinkle NON-SKID DECK ADDITIVE evenly onto the wet coating before it dries. 3. Cover it with the same coating by airless spray, brush or roller. Method B;
1. Before application, thoroughly mix the recommended paint with NON-SKID DECK ADDITIVE in the specified ratio (see "Note"). 2. Apply the mixed paint by brush or roller.
| Weather: temperature | Minimum 0 °C |
|---|---|
| Humidity | Maximum 85% RH |
| Airless spray: viscosity | - |
| Nozzle | - |
| Paint output pressure | - Mpa |
| Spray gun speed | - cm/s |
Thinner:
Previous coat:
Subsequent coat:
| Packaging | One-component |
|---|
Note: 1. Mixing
Recommended for use with the following coatings; specified mixing ratio for application
| (1) EPICON FINISH HB (coating 20 kg | N-SKID AD 6kg) |
|---|---|
| (2) ACRI 700 FINISH G (coating 18 kg | N-SKID AD 6kg) |
| (3) UNY MARINE HS (coating 18 kg | N-SKID AD 6kg) |
| (4) EVAMARINE (coating 19 kg | N-SKID AD 6 kg). 2. Application |
Airless spray: sprinkle NON-SKID DECK SAND evenly onto the wet coating before it dries. After the coating dries, remove excess NON-SKID DECK SAND from the coating surface with a brush or other tool.
Roller and brush: apply NON-SKID DECK SAND mixed in the specified ratio to the coating surface; mix thoroughly before use.
3. If contaminants such as water, oil or grease are present on the coating surface, its anti-skid properties will be weakened.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
