Widely used for corrosion protection of steel surfaces in highly corrosive environments in the petrochemical industry, such as tank interior and exterior walls, oil pipeline interior and exterior walls, and steel structures. Component A is composed of imported special resin, pigments, various functional fillers and additives; Component B is a modified curing agent. Parameters on this page: volume solids 91% ± 2%, dry film thickness 300 µm, theoretical spreading rate 500 g/m². Comparable models from the same brand: ZD100 silane impregnating agent, ZD2551 inorganic hybrid solvent-free primer-finish-in-one coating, ZD6153 Solvent-Free Acid-Resistant Mastic 28:KG.
Parameter source: ZINDN original technical data sheet (TDS) for ZD6345 Stabilised Nano Heavy-Duty Anticorrosive Coating; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 91% ± 2% |
|---|---|
| Dry Film Thickness | 300µm |
| Theoretical Spreading Rate | 500 g/m² |
| VOC | — |
| Density / Specific Gravity | 1.45 ± 0.1 |
| Number of Components | Two-component |
| Flash Point | >25 °C (components A, B and the mixture) |
| Thinner | X-500 Epoxy Thinner |
| Mixing Ratio | Component A (base) : Component B (curing agent) = 6:1 |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
ZD6345 Stabilised Nano Heavy-Duty Anticorrosive Coating
A two-component epoxy-modified high-solids corrosion-resistant coating. Component A is composed of imported special resin, pigments, various functional fillers and additives; Component B is a modified curing agent.
Excellent adhesion, flexibility, impact resistance and abrasion resistance;
Excellent resistance to corrosive media, acid resistance, alkali resistance, water resistance and oil resistance;
Excellent application properties; can be applied and cured on damp surfaces;
Excellent barrier performance, providing equally excellent anticorrosive performance on rusted surfaces.
Widely used for corrosion protection of steel surfaces in highly corrosive environments in the petrochemical industry, such as tank interior and exterior walls, oil pipeline interior and exterior walls, and steel structures.
| Colour | Various colours |
|---|---|
| Solids content by mass | 91%±2% |
| Volume Solids | 86%±2% |
| Mixed density (kg/L) | 1.45±0.1 |
| Typical film thickness and theoretical spreading rate | 500g/m² |
| Wet Film Thickness | 348µm |
| Dry Film Thickness | 300µm |
| New steel | Remove grease from the surface with a suitable cleaner, and wash away salt and other contaminants with fresh water. Remove weld slag, dress welds and sharp edges, and blast clean to Sa 2.5 (ISO 8501-1), with a surface roughness of Rz 30 µm~75 µm. |
|---|---|
| Repair | Remove oil, grease, salts, dust and damaged old coating |
Application ambient temperature 5~38 °C, and the steel surface temperature must be 3 °C above the dew point; outdoor application is prohibited in adverse weather such as rain, fog, snow, strong wind and heavy dust.
| Mixing | This product is supplied as two containers forming one unit. Stir the base thoroughly with a power mixer, add the curing agent in the specified ratio, stir again with a power mixer, and add the recommended thinner to adjust to a suitable application viscosity. Once mixed, use within the specified pot life. |
|---|---|
| Thinner / Cleaning Solvent | X-500 Epoxy Thinner |
| Mixing ratio (by weight) | Component A (base) : Component B (curing agent) = 6:1 |
| Induction Time | 10–30 min (25 °C) |
| 5°C | 15°C | 25°C | 35°C |
| 6 h | 4 h | 3 h | 1 h |
| Application Methods | Airless spray and air spray are recommended; brush and roller are recommended only for touch-up, small-area application or repair. |
|---|
| Application Methods | Unit | High-pressure airless spray | Air Spray | Brush/roller |
| Spray gun tip size | mm | 0.43~0.58 | 1.5~2.5 | —— |
| Spray pressure | kg/cm² | 150~200 | 3~4 | —— |
| Thinning quantity | % | 0~10 | 10~20 | 5~10 |
| Substrate surface temperature | 5°C | 15°C | 25°C | 40°C |
| Touch Dry | 8 h | 4 h | 2 h | 1 h |
| Hard Dry | 48 h | 24 h | 16 h | 12 h |
| Minimum recoat interval | 24 h to 7 days | 16–48 h | 12–24 h | |
| Maximum recoat interval | Unlimited, but any chalk layer from long-term exposure must be removed completely before recoating. |
|---|
Note: the above data are measured under well-ventilated conditions, at typical film thickness and 75% relative humidity, and are for reference only.
and mechanical strength and other factors.
| Subsequent coat | Silicone coatings, polyurethane coatings, fluorocarbon coatings |
|---|
| Packaging Specifications | Component A 24 kg, Component B 4 kg |
|---|---|
| Flash Point | >25 °C (components A, B and the mixture) |
| Storage conditions | Store in accordance with national regulations. Keep in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. |
| Shelf life | Shelf life is 1 year under good storage conditions. |
This product contains flammable materials; site safety must comply with the relevant national or local regulations. Read the safety labels on the packaging and the product Safety Data Sheet (MSDS).
Avoid inhaling solvent vapours and spray mist, avoid contact of paint with skin and eyes, and do not swallow the product. Take the necessary precautions and protective measures for fire prevention, explosion prevention and environmental protection. Use only in well-ventilated conditions. In confined or poorly ventilated areas, provide forced ventilation.
Waste disposal must comply with the relevant national or local regulations.
The information and data in this document are accumulated from our tests and practical experience and may serve as an application guide. Since the use of the product is generally beyond our control, we guarantee only the quality of the product itself. We reserve the right to modify this document without prior notice as the product is improved.
| Version information | Published March 2024; this data sheet supersedes all previous editions. |
|---|
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
