Water-borne Byaqua 5500N Coating is a water-borne coating. One-component water-borne coating for new construction and maintenance protection of metal or concrete substrates. Parameters on this page: volume solids 35 (transparent yellow)/36 (white) ± 2%, dry film thickness 40/50/60 µm, theoretical spreading rate 5.8-6 m²/L.
Parameter source: T&H original technical data sheet (TDS) "Water-borne Byaqua 5500N Coating"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 35 (transparent yellow)/36 (white) ± 2% |
|---|---|
| Dry Film Thickness | 40/50/60 µm |
| Theoretical Spreading Rate | 5.8-6 m2/L |
| VOC | <100g/L |
| Density / Specific Gravity | 1.02 (transparent yellow)/1.19 (white) kg/L |
| Number of Components | One-component |
| Thinner | 0-5% |
| Colour / Appearance | Transparent yellow, white |
| Gloss | High gloss (transparent yellow), semi-gloss (white) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Curing agent: none; thinner: water
One-component water-borne coating for new construction and maintenance protection of metal or concrete substrates
| Colour | Transparent yellow, white |
|---|---|
| Gloss | High gloss (transparent yellow), semi-gloss (white) |
| density | 1.02 (transparent yellow)/1.19 (white) kg/L |
| Volume Solids | 35 (transparent yellow)/36 (white) ± 2% |
| Volatile Organic Compounds | <100g/L |
| Typical dry film thickness | 50µm |
|---|---|
| Recommended dry film thickness | 40–60 µm, depending on system requirements |
| Thinner quantity (by volume) | Airless spray 5–10% | Air spray 10–20% | Roller or brush 0–5% |
| Recommended nozzle size | 0.38~0.43mm | 1.2~2.0mm | / |
| Recommended spray pressure | 15~20MPa | 0.3~0.4MPa | / |
| Application suitability | Recommended | Applicable | |
| Dry film thickness (µm) | 40 | 50 | 60 |
| Wet film thickness (µm) | 114 | 143 | 171 |
| Theoretical spreading rate (m²/L) | 8.75-9 | 7-7.2 | 5.8-6 |
| Temperature | Surface Dry | Hard Dry | Pot Life | Recoat interval | |
| Minimum | Maximum* | ||||
| 15°C | 1h | 6h | / | 6h | / |
| 25°C | 30min | 3h | / | 3h | / |
| 35°C | 20min | 1.5h | / | 3h | / |
*The maximum recoat interval depends on the exposure environment and the end use of the coating.
All surfaces to be coated shall be clean, dry and free from contaminants. Prior to application, all surfaces shall be evaluated and prepared in accordance with ISO 8504:2000. Blast clean to Sa2½ with a surface roughness of 40–75 µm. Before derusting, oil, grease and welding spatter shall be removed completely and welds and sharp edges ground. Where a coating of this product is mechanically damaged and local rusting appears, local repair requires local blast cleaning to Sa2½ or power tool cleaning to St3. When applying over other existing coatings, suitable methods shall be used to remove chalking, zinc salts, grease and other contaminants from the surface. For concrete protection, the concrete shall meet curing requirements, with moisture content and surface condition in accordance with relevant regulations. Confirmation is required before application to other substrates.
1. Provide ventilation and exhaust during application, keep away from ignition sources, and wear protective equipment such as respirators and gloves; maintain adequate ventilation during curing. 2. Adjust the thinner quantity according to temperature changes, mix thoroughly, and filter through a 120-mesh copper wire screen before use. 3. During application and curing, the substrate temperature must be above 5 °C and at least 3 °C above the dew point, moisture content <8%, and relative humidity not exceeding 85%. Temperature and relative humidity shall be measured at the substrate near the work area. Where conditions permit, indoor application is preferred to better ensure the appearance quality of the coating. 4. Cutting structures coated with this product generates fume and dust; provide appropriate protection. 5. When work is paused, do not leave coating in paint lines, spray guns or spray equipment. Flush all equipment thoroughly with thinner. If the pause is prolonged, remix a fresh batch of paint for application. 6. Clean all equipment with thinner immediately after use. Regular flushing of spray equipment during daily work is good practice. Cleaning frequency depends on spray volume, temperature, spraying time and interruption time, among other factors. 7. Dispose of leftover paint and empty cans in accordance with applicable regional regulations.
| 10.2 kg (transparent yellow)/11.9 kg (white) | 20.4 kg (transparent yellow)/23.8 kg (white) |
|---|---|
| 10L | 20L |
Store sealed in a ventilated, cool and dry place away from ignition sources. The ideal storage temperature is 5-35°C. Prevent freezing at 0°C or exposure to high temperatures. Minimum 12 months.
1. For the coating and its recommended thinners, see the safety sheets and the safety data of the relevant materials. This is a solvent-borne coating; avoid inhaling spray mist and solvent vapours, and avoid exposing skin and eyes and contact with uncured paint as far as possible. 2. All work related to the application and use of this product must comply with the relevant national health, safety and environmental standards and regulations. 3. If welding or flame cutting is required on metal coated with this product, dust and fumes will be generated; use appropriate personal protective equipment and adequate local ventilation. 4. If in doubt about the suitability of this product, consult the company.
The information provided in this product data sheet is based on laboratory test results that we consider accurate, and is provided for application guidance only. All recommendations and advice given by T&H on the use of T&H products, whether in technical documents, special consultation or otherwise, are based on information we consider most reliable. Our products and the information provided are intended for users with the necessary knowledge and industrial experience, and it is for these end users to determine whether the products are suitable for their use. T&H cannot control the quality and condition of the substrate, nor the various factors affecting the use of the product. Therefore, T&H accepts no liability for any loss, injury or damage arising from the use of our products or from reliance on this product data sheet (unless otherwise agreed in writing). Data in this product data sheet may be revised as necessary based on practical experience and continued product development.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
