3Tree FFZ042-LG High-solids Micaceous Iron Oxide Epoxy is an epoxy coating used as an intermediate coat. It offers fast drying and rapid recoating, contains micaceous iron oxide pigment and provides a good barrier effect. Parameters on this page: volume solids 70 ± 2%, dry film thickness 100–200 µm, theoretical spreading rate 0.29.
Parameter source: 3Tree manufacturer's Technical Data Sheet (TDS) "3Tree FFZ042-LG High-solids Epoxy MIO Paint"; spreading rate and other values are converted from TDS parameters and are for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 70 ± 2% |
|---|---|
| Dry Film Thickness | 100–200 µm |
| Theoretical Spreading Rate | 0.29 L/m2 |
| VOC | 300 g/L |
| Density / Specific Gravity | Approx. 1.8 kg/L |
| Number of Components | Two-component |
| Flash Point | 32 °C |
| Thinner | FFX001 Epoxy Universal Thinner |
| Mixing Ratio | Base FFZ042A-LG : Hardener FFZ042B-LG = 4:1 (vol… |
3Tree FFZ042-LG High-solids Epoxy MIO Paint
A two-component, high-solids, fast-drying epoxy high-build coating used as an intermediate coat in coating systems; widely applicable to steel structures or concrete elements in petrochemical, power and energy, infrastructure and other industries.
Fast-drying and rapid recoating properties; contains micaceous iron oxide pigment and provides a good barrier effect.
| Colour: | Grey, Iron Red |
|---|---|
| Gloss: | Semi-gloss |
| Volume solids: | 70±2% |
| Specific gravity: | Approx. 1.8 kg/L |
| Flash point: | 32 °C |
| VOC content: | 300 g/L |
| Mixing ratio: | Base FFZ042A-LG : Hardener FFZ042B-LG = 4:1 (by volume) |
|---|---|
| Thinner | FFX001 Epoxy Universal Thinner |
| Recommended dry film thickness: | 100–200 µm |
| Induction time: | No induction required |
| Recommended Thinner Addition (by weight) | Airless spray, as required* | Air spray, as required* | Roller or brush, as required* |
| Recommended nozzle size | 0.43mm | 1.5mm | / |
| Recommended spray pressure | 15-25MPa | 0.4-0.6MPa | / |
| Application suitability | Recommended | Applicable | Repair |
*Thinner addition improves application viscosity. For spraying, the amount added is based on a satisfactory spray gun test and shall comply with the VOC emission requirements of national laws and regulations. Airless spray is preferred for this product; roller and brush application are suitable for small-area repair only.
| Dry film thickness (µm) | 100 | 150 | 200 |
| Theoretical Consumption (L/m²) | 0.14 | 0.21 | 0.29 |
| Theoretical consumption (kg/m²) | 0.26 | 0.39 | 0.51 |
*Practical consumption is affected by equipment, operator technique and application environment; determine the practical consumption according to actual conditions.
Recoat time* Temperature
| -5°C | Minimum (hours): 12 | Maximum (days) 45 |
| 10°C | 4 | 30 |
| 20°C | 2 | 14 |
| 30°C | 1 | 7 |
| -- The recoat interval depends on the subsequent exposure conditions | If the maximum recoat interval is exceeded, abrade the primer surface to ensure intercoat adhesion. Surfaces exposed to a contaminated environment must be washed clean with high-pressure fresh water and allowed to dry before recoating. |
|---|
Drying and curing schedule for 100 µm dry film thickness
| Temperature | Touch dry (h) | Full cure (days) | Pot life (h) |
| -5°C | 12 | 14 | 4 |
| 10°C | 4 | 12 | 2 |
| 20°C | 2 | 7 | 1 |
| 30°C | 1 | 5 | 0.5 |
- Adequate and continuous ventilation must be maintained during application and curing of the coating.
- When applying at ambient air or substrate surface temperatures below 5 °C, pre-warm the mixed paint to above 10 °C.
As an intermediate coat in a coating system, the previous coat shall be within the recoat interval before any coating is applied, and the surface to be overcoated shall be free from oil, water and other contaminants. Areas with mechanical damage or local rusting shall be spot abrasive blast cleaned to Sa2½ or power tool cleaned to St3 for local repair of the previous coat. If the recoat interval is exceeded, the surface shall be abraded, degreased, dewatered and cleaned of other contaminants.
| FFZ042A-LG High-solids Epoxy MIO Paint: | 32.2 kg/drum |
|---|---|
| FFZ042B-LG High-solids Epoxy MIO Paint Hardener: | 3.8 kg/drum |
For the coating and its recommended thinners, see the safety sheets and the relevant Material Safety Data Sheet.
This is a solvent-borne coating; use the necessary protective equipment and avoid inhaling spray mist and solvent vapours.
In addition, avoid contact of uncured paint with skin and eyes.
In all cases, SKSHU (3TREES) shall not be liable for any indirect, special, incidental or consequential loss of any kind arising from or in connection with the use of this product (whether based on negligence, strict liability or tort).
The information contained in this Data Sheet is derived from laboratory tests that we believe to be reliable, but is intended as a guide only. As application experience accumulates and product development continues, 3Tree may at any time revise the above information and all recommendations or suggestions relating to this product, whether in technical documents, in replies to specific enquiries or by other means; the data and information provided reflect the full extent of our knowledge and are reliable. Our products and related information are supplied specifically for industrial users with the necessary knowledge and practical skills; end users of the product are responsible for determining whether the product is suitable for their particular application. Purchasers are therefore expected to have carried out such an evaluation and to accept full responsibility and the corresponding risk.
The quality and condition of the substrate on site, and the many other factors affecting product use and application, are beyond SKSHU (3TREES)'s control.
SKSHU (3TREES) accepts no liability for coating quality problems caused by application environment, application process, surface preparation or personnel operation (unless otherwise provided in a written agreement).
To avoid misuse, confirm with our sales staff that the product data sheet in hand is the latest version.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
The in-house item numbers of 3Tree FFZ042-LG High-solids Epoxy MIO Paint are listed below.Item No.is the most accurate form when ordering;Colour/colour codecorresponds to the actual colour (RAL, GSB are colour chart codes);Packaging SpecificationsFactory complete-set specification format. Colors not listed may be ordered against the colour card.
| Item No. | Colour / colour code | Packaging Specifications |
|---|---|---|
| FFZ042-LG | — | 36 KG |
| FFZ042-MIO | — | 36 KG |
This model has a total of2item numbers, all listed on this page; colours outside the table (including special colours and bulk packaging) can be confirmed by phone, delivery dates are advised according to the factory's current production schedule and stock. In the packaging specification, the "+" indicates the complete-set notation for two-component products (base + curing agent), subject to the factory specification; a "—" in the colour column denotes an auxiliary product, or that the item has no colour code in the factory system.
