SKSHU FFD008ST Epoxy Zinc-rich Primer is a zinc-rich primer in the epoxy system. Features fast drying and fast recoating, wide compatibility and suitability for various application methods. Parameters on this page: volume solids 60 ± 2%; dry film thickness 50–125 µm; theoretical spreading rate 8 m²/L.
Source: SKSHU 3TREES original technical data sheet (TDS) 'SKSHU FFD008ST Epoxy Zinc-rich Primer'. Spreading rate and other values converted from the TDS; for reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 60 ± 2% |
|---|---|
| Dry Film Thickness | 50–125 µm |
| Theoretical Spreading Rate | 8 m²/L (at 75 µm DFT) |
| VOC | 320 g/L |
| Density / Specific Gravity | Approx. 1.7 kg/L |
| Number of Components | Two-component |
| Flash Point | 24 °C |
| Thinner | FFX001 Epoxy Universal Thinner |
| Mixing Ratio | Base FFD008STA : hardener FFD008STB = 85:15 (by vo… |
SKSHU FFD008ST Epoxy Zinc-rich Primer
FFD008ST is a two-component epoxy zinc powder primer. After curing it forms a hard, corrosion-resistant film. As a primer based on an electrochemical anticorrosive mechanism, it is suitable for anticorrosive protection of building steel structures, pipelines and machinery in corrosive environments.
Features fast drying and fast recoating, wide compatibility and suitability for various application methods.
| Colour: | Zinc grey, red grey |
|---|---|
| Gloss: | Matt |
| Volume solids: | 60±2% |
| Specific gravity: | Approx. 1.7 kg/L |
| Recommended dry film thickness: | 50–125 µm |
| Flash point: | 24 °C |
| Theoretical Spreading Rate | 8 m²/L (at 75 µm DFT) |
| VOC content: | 320 g/L |
| Fully cured | 7 days |
| Storage time | Dry, cool environment, 12 months |
| Mixing ratio: | Base FFD008STA : hardener FFD008STB = 85:15 (by volume) |
|---|---|
| Thinner: | FFX001 Epoxy Universal Thinner |
| Thinner | Airless spray 0–5%* | Air spray 0–5%* | Roller or brush 0–5%* |
| Recommended nozzle size | 0.43-0.48mm | 1.0-2.0mm | / |
| Recommended spray pressure | 15-25MPa | 0.3-0.6MPa | / |
| Application suitability | Recommended | Applicable | Repair |
*Thinner improves application viscosity; for spraying, the addition is based on a satisfactory gun test, but must comply with national VOC emission regulations. Airless spray is preferred; roller and brush are suitable for small-area repair only.
| Dry film thickness (µm) | 50 | 75 | 125 |
| Theoretical consumption (L/m²) | 0.08 | 0.13 | 0.21 |
| Theoretical consumption (kg/m²) | 0.14 | 0.21 | 0.35 |
*Practical consumption is affected by equipment, operator technique and application environment; determine the practical consumption according to actual conditions.
Recoat time* Temperature
| 0°C | Minimum (hours): 6 | Maximum (days) 60 |
| 10°C | 4 | 45 |
| 20°C | 2 | 30 |
| 30°C | 1 | 14 |
Zinc salts form on zinc-rich primer surfaces; before overcoating, the coating shall not be exposed outdoors for prolonged periods.
Before overcoating, any visible contamination on the surface shall be removed as appropriate, by high-pressure water washing, sweep blasting or power tool cleaning depending on the situation.
| Temperature | Touch dry (h) | Full cure (days) | Pot life (h) |
| 0°C | 5 | 14 | 8 |
| 10°C | 3 | 12 | 4 |
| 20°C | 2 | 7 | 1 |
| 30°C | 1 | 5 | 0.5 |
- Adequate and continuous ventilation must be maintained during application and curing of the coating.
- When applying at ambient air or substrate surface temperatures below 5 °C, pre-warm the mixed paint to above 10 °C.
Abrasive blast clean to Sa 2½ (ISO 8501-1) or at least SSPC-SP6, with surface roughness 40–70 µm after blasting.
| Surfaces coated with a type-approved inorganic zinc silicate shop primer | Sweep blast clean to Sa 1 (ISO 8501-1) (SSPC-SP7) or prepare with power tools to St 3 (ISO 8501-1) (SSPC-SP3). |
|---|
| FFD008STA Epoxy Zinc-rich Primer: | 27.52 kg/drum |
|---|---|
| FFD008STB Epoxy Zinc-rich Primer Hardener | 2.48 kg/drum |
For the coating and its recommended thinners, see the safety sheets and the relevant Material Safety Data Sheet.
This is a solvent-borne coating; use the necessary protective equipment and avoid inhaling spray mist and solvent vapours.
In addition, avoid contact of uncured paint with skin and eyes.
In all cases, SKSHU (3TREES) shall not be liable for any indirect, special, incidental or consequential loss of any kind arising from or in connection with the use of this product (whether based on negligence, strict liability or tort).
The information in this data sheet is based on laboratory tests that we believe to be reliable, but is provided for reference and subject to revision.
All recommendations and advice concerning the use of this product, whether in technical documents, in response to an enquiry or otherwise, are given to the best of our knowledge and are believed to be reliable. Our products and related information are provided for industrial users possessing the necessary knowledge and practical skills, and it is the end user's responsibility to determine whether the product is suitable for the specific use. The buyer, having performed such evaluation, proceeds entirely at its own risk.
The quality and condition of the substrate on site, and the many other factors affecting product use and application, are beyond SKSHU (3TREES)'s control.
SKSHU (3TREES) accepts no liability for coating quality problems caused by application environment, application process, surface preparation or personnel operation (unless otherwise provided in a written agreement).
To avoid misuse, confirm with our sales staff that the product data sheet in hand is the latest version.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
The factory item numbers of SKSHU FFD008ST Epoxy Zinc-rich Primer are as follows.Item No.is the most accurate form when ordering;Colour/colour codecorresponds to the actual colour (RAL, GSB are colour chart codes);Packaging SpecificationsFactory complete-set specification format. Colors not listed may be ordered against the colour card.
| Item No. | Colour / colour code | Packaging Specifications |
|---|---|---|
| FFD008ST | — | 30 KG |
This model has a total of1item numbers, all listed on this page; colours outside the table (including special colours and bulk packaging) can be confirmed by phone, delivery dates are advised according to the factory's current production schedule and stock. In the packaging specification, the "+" indicates the complete-set notation for two-component products (base + curing agent), subject to the factory specification; a "—" in the colour column denotes an auxiliary product, or that the item has no colour code in the factory system.
