PPG SIGMACOVER 410 AMERCOAT 410 High-solids Epoxy Coating 410 is an epoxy coating. Two-component high-solids polyamide-cured epoxy mastic, also available in a micaceous iron oxide version. Even after prolonged exterior weathering, the coating can still be overcoated with two-component coatings and conventional one-component alkyd coatings. Specifications on this page: volume solids 80 ± 2%, DFT 75-200 µm (3.0-8.0 mil) depending on system requirements, theoretical spreading rate 10.7 m²/L.
Source: PPG original technical data sheet (TDS) 'PPG SIGMACOVER 410 AMERCOAT 410 High-solids Epoxy 410'. Spreading rate and other values converted from the TDS; for reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 80 ± 2% |
|---|---|
| Dry Film Thickness | 75–200 µm (3.0–8.0 mil) depending on the coating system requirements |
| Theoretical Spreading Rate | 10.7 m²/L |
| VOC | Max 126.0 g/kg (EU Directive 1999/13… |
| Density / Specific Gravity | 1.5 kg/L (12.5 lb/US gal), depending on version and colour |
| Number of Components | Two-component |
| Thinner | Thinner 91-92 |
| Recoat Interval | Minimum: 8 h |
| Introduction | A two-component, high-solids, polyamide-cured epoxy high-build paint, also available in a micaceous iron oxide version |
|---|
| Number of Components | Two-component |
| Density | 1.5 kg/L (12.5 lb/US gal), depending on version and colour |
MIO version: 1.9 kg/L (15.9 lb/US gal)
| Volume solids | 80 ± 2% |
| VOC (as supplied) | Max 126.0 g/kg (EU Directive 1999/13/EC, SED) |
UK PG 6/23(92) Annex 3: max 240.0 g/L (approx. 2.0 lb/US gal)
| Recommended dry film thickness | 75–200 µm (3.0–8.0 mil) depending on the coating system requirements |
| Theoretical Spreading Rate | 10.7 m²/L at 75 µm (428 in²/US gal at 3.0 mils) |
| Touch Dry | 3 h |
| Recoat Interval | Minimum: 8 h |
Maximum: extended accordingly
| Full cure time | 7 days |
| Storage shelf life | Base: at least 24 months; store in a dry and cool environment |
Curing agent: at least 24 months; store in a dry and cool environment
otherwise thinner may be needed to adjust the paint viscosity to a suitable application state.
| Induction Time | Not required |
|---|
6 h at 20 °C (68 °F). Note: refer to supplementary data — pot life
| Recommended thinner | Thinner 91-92 |
|---|---|
| Thinner quantity | 0–10%; 30–40% for mist coat application |
| Nozzle tip size | Approx. 0.46–0.53 mm (0.018–0.021 in) |
| Nozzle pressure | 20.0–25.0 MPa (approx. 200–250 atm; 2901–3626 psi) |
| Recommended thinner | Thinner 91-92 |
|---|---|
| Thinner quantity | 0 - 5% |
| Cleaning solvent | Thinner 90-53 |
| Dry Film Thickness | Theoretical Spreading Rate |
| 75 µm (3.0 mils) | 10.7 m²/L (428 in²/US gal) |
| 150 µm (6.0 mils) | 5.3 m²/L (214 in²/US gal) |
| 200 µm (8.0 mils) | 4.0 m²/L (160 in²/US gal) |
| Subsequent coat for recoating | Recoat interval | 5°C (41°F) | 10°C (50°F) | 20°C (68°F) | 30°C (86°F) | 40°C (104°F) |
| Can be overcoated with various two-component | Minimum time | 36 h | 24 h | 8 h | 6 h | 4 h |
| Epoxy or polyurethane topcoat | Maximum time | Extendable | ||||
| Substrate Temperature | Surface Dry | Fully hard dry | Fully cured |
| 5 °C (41 °F) | 12 h | 30 h | 20 days |
| 10 °C (50 °F) | 6 h | 24 h | 14 days |
| 15 °C (59 °F) | 4 h | 10 h | 10 days |
| 20 °C (68 °F) | 3 h | 8 h | 7 days |
| 30 °C (86 °F) | 2 h | 6 h | 5 days |
| 40 °C (104 °F) | 1.5 h | 4 h | 3 days |
Note: ensure continuous, adequate ventilation during application and curing (see Safety Sheet 1433 and Information Sheet 1434). Pot life after mixing (at suitable application viscosity)
| Mixed paint temperature | Pot life after mixing |
| 10 °C (50 °F) | 12 h |
| 15 °C (59 °F) | 10 h |
| 20 °C (68 °F) | 6 h |
| 25 °C (77 °F) | 4 h |
| 30 °C (86 °F) | 3 h |
| 40 °C (104 °F) | 2 h |
Although PPG Protective and Marine Coatings is committed to providing completely consistent products to users worldwide, from time to time it may be necessary to make minor adjustments to specific products to comply with local/national regulations or environmental requirements. In the following cases, use the corresponding alternative version of the product data sheet instead.
PPG warrants (1) that it has good title to the product, (2) that the product quality conforms to the relevant technical quality specifications in force at the date of manufacture of the product, and (3) that the supplied product is free of lawful claims by third parties for infringement of US patent rights. The above warranties are limited to those given by PPG and other express or implied warranties required by applicable laws and regulations for transactions and commercial practice; any abuse contrary to the stated conditions, and any other warranty for special purposes or uses, are excluded, and PPG shall be free from liability. To claim under this warranty, the buyer must notify PPG in writing within five (5) days of discovering the quality defect, and the date must be within the product's valid storage period or within one (1) year from delivery of the product to the buyer. If the buyer fails to notify PPG of the defect as required above, this will prejudice the buyer's right to obtain compensation under this warranty from PPG!
In all cases, PPG shall not be liable for any indirect, special, incidental or consequential loss of any kind arising from or in connection with the use of this product (whether based on negligence, strict liability or tort).
The information in this product data sheet is based on laboratory tests we believe to be reliable, and is provided for guidance only.
PPG may revise this information at any time as experience accumulates and product development progresses.
All recommendations and advice concerning the use of this product, whether in technical documents, in response to an enquiry or otherwise, are given to the best of our knowledge and are believed to be reliable.
Our products and related information are provided for industrial users possessing the necessary knowledge and practical skills, and it is the end user's responsibility to determine whether the product is suitable for the specific use. The buyer, having performed such evaluation, proceeds entirely at its own risk. The quality and condition of the substrate on site, and the many other factors affecting product use and application, are beyond PPG's control. Therefore, PPG accepts no liability for any loss, injury or damage arising from the use of the information in this product data sheet (unless otherwise provided in a written agreement). Different application environments, changes to the application process or extrapolation of the reference data may result in failure to achieve the expected coating quality.
This product data sheet supersedes all previous versions. The buyer is responsible for confirming that the data sheet in hand is the latest version before using the product. The latest version is published on the official website of PPG Protective & Marine Coatings: www.ppgpmc.com. In case of discrepancy between the Chinese version and the original English version of the product data sheet, the English original shall prevail.
The PPG Logo, Bringing innovation to the surface., and other PPG marks are property of the PPG group of companies. All other third-party marks are property of their respective owners.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
