Remove all laitance and debris by washing, scraping or light blasting. Parameters on this page: volume solids 55 ± 2%, dry film thickness 50 µm, theoretical spreading rate 5.5 m²/L/100 µm. Comparable products from the same brand: AMERCOAT 114 A Epoxy Filler 114 A, AMERCOAT 220 Waterborne Acrylic Topcoat 220, AMERCOAT 240 SIGMACOVER 240 High-solids Multipurpose Epoxy 240.
Source: PPG original technical data sheet (TDS) "CENTRIFUGON EAP"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | — |
|---|---|
| Dry Film Thickness | — |
| Theoretical Spreading Rate | — |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Thinner | Apply with Thinner No. 22 |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
Performance: indoor; outdoor. Approved for use in nuclear power plants by EDF (Électricité de France), CEMETE, CEA and BINE (Beijing Nuclear Institute No. 2). (Passed radiation and shop/site painting;
LOCA composite test, meets PIC system) painting;
Complies with ANSI N512, 101.2. New construction; maintenance;
Provides good chemical resistance, used in areas contaminated by aromatic, aliphatic and chlorinated solvents.
Can be in occasional contact with dilute acidic or alkaline substances. Applicable environments: generally aggressive environments.
Complies with PMUC specification characteristics (20 °C, 65% relative humidity). Product appearance: glossy. Recommended dry film thickness 50 µm. Colour: refer to the "Feida" colour chart. Recommended wet film thickness 90 µm. Composition: two-component. Theoretical spreading rate for 50 µm dry film: 11 m²/L. Mixing ratio by volume. Drying time for 50 µm dry film:
Base: 70%. Dust-free: 1 h 30 min. Curing agent: 30%. Touch dry: 3 h. Handling: 12 h. Thinner: Thinner No. 22. Recoatable. Induction time: none; pot life 8 h. *Ambient temperature affects pot life and minimum recoat interval. Density 1.26 ± 0.05. Recoat interval for 50 µm dry film:
Solids content by volume: 55% ± 2. Minimum*: 12 h – maximum*: 1 year. Temperature resistance: continuous 100 °C, peak 120 °C (dry). All data relating to the density and solids content of the topcoat are based on the white product. These data are also based on the mixing of the appropriate products.
*See Overview.
CHALLENGING TIMED 7308-98. Substrate types: steel, suitably repaired and dried primer, concrete.
| On steel surfaces | Blast to Sa 2½ per ISO 8501-1. |
|---|---|
| On primed surfaces | Epoxy: Saint Bo, Feida Gao, Feida Bo, Weige EP |
| Concrete | For new work, concrete must have a 3-week curing period. |
|---|
Remove all laitance and debris by washing, scraping or light blasting.
Ensure thorough removal of dust.
Use/thinning
Stir the base mechanically and slowly add the curing agent until thoroughly mixed.
If necessary, thin the product according to the application conditions.
| Thinner: Thinner No. 22 | Cleaning agent: Thinner No. 22 |
|---|---|
| Tools | Thinning, nozzle pressure |
| Brush | Suitable | 0/10% | (for small areas only) | |
| Roller | Suitable | 0/10% | ||
| Air spray gun | Suitable | 15/25% | 14 / 10e | 7 to 4 bar |
| High-pressure spray gun | Suitable | 15/20% | 15 to 17/1000 in | 181–205 bar |
| Application conditions | Ambient temperature: +5 °C to +35 °C |
|---|
Health and safety
| Flash Point | Base and hardener: 21 °C < flash point < 55 °C |
|---|
This figure complies with European paint and varnish sample criteria.
Packaging and storage. Packaging: 20 L (base 14 L / curing agent 6 L). Storage: unopened, indoors between +5 °C and +35 °C, can be stored for 12 months.
Sigma Coatings (China), Room 408, Baiteng Building, 318 Fuzhou Road, Shanghai 200001. Tel: 021-6391-2991; Fax: 021-6391-2700
08-98
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
