No. 1 Thinner: 21°C< Flash Point < 55°C.Parameters on this page: Volume Solids 54 ± 2%, Dry Film Thickness 50 - 70 µm, Theoretical Spreading Rate 5.4 m²/L/100 µm.Comparable models of the same brand: AMERCOAT 114 A Epoxy Filler114 A, AMERCOAT 220 Water-borne Acrylic Topcoat220, AMERCOAT 240 SIGMACOVER 240 High-solids Multi-purpose Epoxy240.
Parameter source: PPG manufacturer's Technical Data Sheet (TDS) "CENTREPOX N EPR"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | — |
|---|---|
| Dry Film Thickness | — |
| Theoretical Spreading Rate | — |
| VOC | RP |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Thinner | Thinner No. 1. Application equipment thinning*, nozzle pressure |
| Packaging Specifications | 02 |
| Shelf life | 01/04 |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
| Type | Use |
|---|---|
| Phenolic Epoxy Primer | Substrate: steel |
| Property | Indoor Outdoor |
| Approved by EDF (Électricité de France), | AREVA, CEA (French Atomic Energy Commission) and immersion |
| COGEMA approval. | Shop application Site application |
| Approved for use in PIC 100/101/103/104 systems (according to CCTR | New construction Maintenance EDF n°91C.031.05.) |
| Approved for use in EPR PIC100 systems | Service environment: nuclear power plants conforming to PMUC specification characteristics (20°C - relative humidity 65%) Product appearance Recommended dry film thickness Semi-gloss 45 to 80 µm Colour Recommended wet film thickness Light ochre yellow 80 to 140 µm Composition Theoretical spreading rate Two-component For 45 µm dry film: 12.5 m²/L Mixing ratio For 80 µm dry film: 7.0 m²/L Drying time By volume Base: 82% For 70 µm dry film: |
Hardener: 18% Dust-free: 1 h Product state Touch dry: 1 h 30 min Thixotropic Thinner Handleable: 6 h No. 1 Thinner Recoatable Induction time CENTREPOX N none in itself Shengfuge EAP Pot life Unitherm coating item 8 h Unitherm 38091 RPE* Ambient temperature affects pot life and the minimum recoat interval Density Suitable recoat interval 90 1.43 ± 0.05 0 For 70 µm dry film: 2.0 Solids content Minimum: 6 h - Maximum: 12 months 1/0 By volume: 56.5% ± 2 Heat resistance 4 By weight: 72% ± 2 Continuous 120°C (dry) D All data relating to the density and solids content of the topcoat are based on the product being white. These data are also based on the product being mixed in the correct ratio.
Substrate type: steel Surface preparation:
Abrasive blast cleaning to Sa 2 1/2 in accordance with ISO 8501-1.
Blast profile: to medium G or Ra 10 to Ra 12.5 in accordance with ISO 8503-1 Use/thinning Product preparation:
Stir the base mechanically, slowly adding the curing agent until fully mixed.
If required, thin the product appropriately according to the application conditions.
| Thinner: Thinner No. 1 | Cleaner: Thinner No. 1. Application equipment thinning*, nozzle pressure |
|---|
| Brush | Suitable | 0–5% (for small areas only) | ||
| Roller | Suitable | |||
| Air Spray | Suitable | 10-20% | 1.4mm | 3 - 4 bars |
| Airless Spray | Suitable | 5-15% | 0.017" – 0.021" | 200 - 250 bars |
*The thinning ratio is adjusted according to weather and specific application conditions.
Application conditions:
| Ambient temperature: +5 °C to +35 °C | Relative humidity controlled below 80%; product temperature preferably above 10°C |
|---|
Health and safety; flash point:
Thinner No. 1: 21 °C < flash point < 55 °C
| VOC content: 403 g/L | Item |
|---|---|
| VOC data vary slightly with colour and thinner used. | RP |
| MSDS available at www.quickfds.com (Supplier FREITAG) | E for packaging and storage 90 |
| Packaging: 20 L (Base: 16.4 L / Hardener: 3.6 L), 5 L (Base: 4.1 L / Hardener: 0.9 L) | 02. |
| Storage: unopened indoors at +5°C to +35°C; for storage life refer to the product label. | 01/04 |
| AFNOR classification (NFT 36005): | Class I, grade 6b, D |
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
