200 H SILVER M alkyd topcoat, heat-resistant and oil-resistant, maximum resistance temperature up to 150 °C. Parameters on this page: Number of Components: one-component.
Parameter source: NIPPON MARINE original technical data sheet (TDS) \"TETZSOL 200 H\"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 48 ± 2% |
|---|---|
| Dry Film Thickness | 20-30 µm |
| Theoretical Spreading Rate | 19.2 m²/L (25 µm) |
| VOC | 417 g/L |
| Density / Specific Gravity | — |
| Number of Components | One-component |
| Flash Point | 31.5°C |
| Thinner | THINNER 100 thinner is usually not required. When applying under extreme conditions, please consult… |
| Colour / Appearance | Silver |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
| Publication date | July 2024 |
|---|---|
| TETZSOL | 200 H SILVER M alkyd topcoat, heat-resistant and oil-resistant, maximum resistance temperature up to 150 °C. |
Product Data
Heat-resistant topcoat, for engines, boilers, etc.
| Type | Alkyd (maximum heat resistance 150 °C) |
|---|---|
| Colour | Silver |
| Gloss | |
| Volume Solids | 48 ± 2% (ISO3233:1998) |
| Dry Film Thickness | 20 ~ 30 µm |
| Wet Film Thickness | 42 ~ 63 µm |
| Theoretical Spreading Rate | 19.2 m²/ L (25 µm) |
| Drying Time | Surface Dry | 2 h (5 °C) | Hard Dry | 7 h (5 °C) |
| 1 h (20 °C) | 4 h (20 °C) | |||
| 45 min (30 °C) | 3 h (30 °C) | |||
| Recoat interval | Minimum | 24 h (5 °C) | Maximum | -- (5°C) |
| (self-recoat) | 16 h (20 °C) | -- (20°C) | ||
| 16 h (30 °C) | -- (30°C) |
| VOC | 417 g/L (GB/T 23985-2009) |
|---|
All surfaces to be coated must be clean, dry and free of contaminants. Wash with high-pressure fresh water to remove all oil, grease, soluble salts and foreign matter
| Thinner | THINNER 100 thinner is usually not required. When applying under extreme conditions, please consult local NIPPON MARINE coatings personnel. |
|---|
Airless Spray
| Gun tip size | 0.33 mm |
|---|---|
| Spray fan angle | 55° ~ 69° |
| Output pressure | 120 ~ 150 kg/cm² Brush/Roller For small-area repair only |
| Packaging Specifications | Single component: 20 L; packaging may vary by origin |
| Flash Point | 31.5°C(GB/T 5208-2008) |
Take the necessary protective measures to avoid skin and eye contact (e.g. gloves, safety glasses, face shield, barrier cream).
Ensure adequate ventilation during application and drying to keep solvent vapour concentrations within safe limits.
Before use, refer to the health and safety information in the Safety Data Sheet (SDS) for this product.
Precautions: 1. The content of this product data sheet may be revised at any time as our experience grows and the product is further developed.
2. If the film temperature rises too quickly due to machine operation during drying, detachment may occur. To avoid this, heat up slowly at no more than 10 °C per minute or stop machine operation intermittently.
3. The VOC value may vary due to tolerances in the production process.
| 4. TETZSOL | 200 H SILVER M is supplied in China only. |
|---|
5. For product selection, consult local Nippon Paint Marine Coatings personnel.
6. Packaging and can quantities may vary due to local regulations.
7. The product shall be stored in a paint warehouse.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
