Used as an anticorrosive coating for freeboards, weather decks, deck outfittings, hatch covers, exterior superstructures, cargo holds, engine rooms, pump rooms, void spaces and cofferdams, etc. Good water resistance and anticorrosion, can be applied directly over chlorinated rubber, acrylic and alkyd coatings. Parameters on this page: volume solids 61 ± 2%, theoretical spreading rate 6.10 m²/L (100 µm), number of components two.
Source: NIPPON MARINE original technical data sheet (TDS) "NEOGUARD 100 Surface-tolerant Epoxy"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 61 ± 2% |
|---|---|
| Dry Film Thickness | 100-200µm |
| Theoretical Spreading Rate | 6.10 m²/ℓ (100µm) |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Thinner | THINNER 600 (0–10%, by weight) |
| Mixing Ratio | Base : curing agent = 15.9 : 4.1 |
| Colour / Appearance | White base –GBN095, cream base –GBS332, iron red base –GBJ… |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A flexible, surface-tolerant, two-component multipurpose epoxy coating mainly for maintenance and repair, strengthening the protection of freeboards, decks, cargo holds, exterior superstructures and other areas, combining anticorrosive and topcoat functions, and applicable directly to hand-cleaned surfaces or old coatings. Using this product keeps vessels in service maintenance-free for a long time. Good water resistance and anticorrosion, can be applied directly over chlorinated rubber, acrylic and alkyd coatings.
Used as an anticorrosive coating for freeboards, weather decks, deck outfittings, hatch covers, exterior superstructures, cargo holds, engine rooms, pump rooms, void spaces and cofferdams, etc.
| Type | Epoxy (high-build/surface-tolerant/two-component) |
|---|---|
| Colour | White base –GBN095, cream base –GBS332, iron red base –GBJ445, curing agent –GBA302, black, grey (070, 060, 040), green |
| Gloss | Semi-gloss |
| Solids content (by volume) | 61 ± 2% (ISO3233:1998) |
| Mixing ratio (by volume) | Base : curing agent = 15.9 : 4.1 |
| Recommended film thickness | Dry film: 100–200 µm |
| Wet film | 164 ~ 328µm |
| Theoretical Spreading Rate | 6.10 m²/ℓ (100µm) |
| Thinner | THINNER 600 (0–10%, by weight) |
| 5°C | 20°C | 30°C | ||
| Drying Time | Surface Dry | 2 h | 1 h | 40 min |
| Hard Dry | 24 h | 12 h | 6 h | |
| Fully cured | 14 days | 7 days | 5 days | |
| Recoat interval | Minimum | 24 h | 12 h | 6 h |
| (self-recoat) | Maximum | ----- | ----- | |
| Pot life | 5 h | 3 h | 2 h |
| Flash Point | Base 19 °C, curing agent 15 °C |
|---|
Airless spray; nozzle size: 0.48–0.59 mm
| Spray fan angle | 55–62° (repair: 30°) |
|---|---|
| Output pressure | 150~200 kg/㎝2 |
Blast to Sa 2.0 or power-tool clean to St 2.0
| Packaging Specifications | 20 L (base 15.9 L, curing agent 4.1 L) |
|---|
Take the necessary protective measures to avoid skin and eye contact (e.g. gloves, safety glasses, face shield, barrier cream). Ensure adequate ventilation during application and drying to keep solvent vapour concentrations within safe limits.
Before use, refer to the health and safety information in the Material Safety Data Sheet (MSDS) for this product.
1) The content of this product data sheet may be revised at any time as our experience grows and the product is further developed.
2) Although heavy rust has been removed, pitted areas may still retain salts and soluble rust; flush with high-pressure fresh water.
3) For severely rusted areas, first treat per method 2) above, then apply NEOGUARD BULCON, and then apply the full NEOGUARD 100 system.
4) One further coat of epoxy or polyurethane topcoat may be applied for better anticorrosion and appearance; consult Nippon Marine Paint personnel for details.
5) Store in the paint warehouse.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
