ECOLOFLEX SPC 250 HyB Tin-free Self-polishing Antifouling 250 is an antifouling coating. Antifouling for ocean-going vessels (medium speed, low speed). This product uses patented copper silyl acrylate polymer technology; through durable and stable low-friction coating properties, the active surface of the coating remains continuously exposed to seawater, thereby achieving antifouling performance. Parameters on this page: volume solids 52 ± 2%, theoretical spreading rate 5.2 m²/L (dry film 100 µm).
Parameter source: nippon-marin manufacturer technical data sheet (TDS) \"ECOLOFLEX SPC 250 HyB Tin-free Self-polishing Antifouling 250\"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 52 ± 2% |
|---|---|
| Dry Film Thickness | 80µm ~ 150µm |
| Theoretical Spreading Rate | 5.2 m²/L (dry film 100 µm) |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | — |
| Flash Point | 24°C |
| Thinner | THINNER 300 (thinning by volume: 0–5%) |
| Colour / Appearance | Cherry red V — BRA006, purple-red V — BRA007 |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
This product uses patented copper silyl acrylate polymer technology; through durable and stable low-friction coating properties, the active surface of the coating remains continuously exposed to seawater, thereby achieving antifouling performance.
Complies with the international convention requirements adopted by the International Maritime Organization in October 2001 on the control of harmful anti-fouling systems on ships (IMO document AFS/CONF/26).
Antifouling for ocean-going vessels (medium speed, low speed)
| Type | Copper silyl acrylate polymer (tin-free/low friction/hydrolysing/high solids) |
|---|---|
| Colour | Cherry red V — BRA006, purple-red V — BRA007 |
| Gloss | Semi-gloss |
| Solids content (by volume) | 52 ± 2% (ISO3233:1998) |
| Recommended film thickness | DFT: 80–150 µm |
| Wet film | 154µm ~ 288µm |
| Theoretical Spreading Rate | 5.2 m²/L (dry film 100 µm) |
| Thinner | THINNER 300 (thinning by volume: 0–5%) |
| 5°C | 20°C | 30°C | ||
| Drying parameters | Surface Dry | 1 h | 40 min | 30 min |
| Hard Dry | 3 h | 1 h | 40 min | |
| Recoat interval | Minimum | 6 h | 4 h | 3 h |
| (self-recoat) | Maximum | ----- | ----- | |
| Interval before immersion (100 µm) | 18 h | 12 h | 10 h |
※See note 4)
| Flash Point | 24°C |
|---|
Airless spray: tip size 0.69–0.84 mm
| Spray fan angle | 60 ~ 75° |
|---|---|
| Output pressure | Above 150 kg/cm² |
For small-area repair only
All surfaces to be coated must be clean, dry and free of contaminants. Wash with high-pressure fresh water to remove all oil, grease, soluble salts and foreign matter
| Packaging Specifications | 20 L (packaging may vary by origin) |
|---|
Take the necessary protective measures to avoid skin and eye contact (e.g. gloves, safety glasses, face
1) The content of this product data sheet may be revised at any time as our experience grows and the product is further developed.
2) Before and after use, clean spray equipment, lines and spray guns with THINNER 300.
3) If mixed with other antifoulings or any other chemicals, the product will not qualify for the 'tin-free antifouling declaration'.
4) The interval before immersion depends on the surrounding environmental conditions, ventilation, film thickness and number of coats, and is affected accordingly. Contact us during actual application.
5) Store the product in a paint warehouse.
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
