THERMOTECT WR Heat-resistant Coating WR is a heat-resistant coating. For high-temperature steel structures with or without insulation. Under Insulation). An inorganic copolymer heat-resistant coating for CUI (corrosion under insulation) protection. Specifications on this page: volume solids 54 ± 2%, number of components: two-component. Comparable products of the same brand and type: THERMOTECT EP Epoxy Heat-resistant Coating EP, SLICON AC-250 TOPCOAT Silicone Heat-resistant Topcoat AC-250, THERMO 600 FINISH Silicone Heat-resistant Topcoat 600.
Parameter source: KANSAI original Technical Data Sheet (TDS) 'THERMOTECT WR Heat-resistant Coating WR'; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 54 ± 2% |
|---|---|
| Dry Film Thickness | 100–150 µm per coat |
| Theoretical Spreading Rate | — |
| VOC | 396g/L |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Flash Point | 25°C |
| Thinner | Dedicated thinner X |
| Mixing Ratio | Base/Hardener=19/1(by weight) |
| THERMOTECT WR | Heat-resistant Coating WR |
|---|
A heat resistance paint based on inorganic copolymer for preventing CUI(Corrosive
An insulated and non insulated steel structure for high temperature services
Suitable for high temperature(up to 650°C)
Suitable for insulated and non insulated surface
Cyclic services in temperature between -185°C-540°C
Good applicability
Good weather resistance
| Color | Grey with aluminium effect |
|---|---|
| Colour | Aluminium grey |
| Volume Solids | 54±2% |
| VOC | 396g/L, |
| Volatile organic compound content | 396g/L |
| Flash Point | 25°C |
| Flash Point | Dry :100-150 microns/coat Wet : 185-278microns/coat |
| Film thickness | DFT: 100–150 µm/coat WFT: 185–278 µm/coat |
| Applied film thickness | 0.344Kg/m2/125 microns |
0.344 kg/m²/125 µm
| Theoretical Coverage | Practical coverage depending on surface conditions, environment, applications, etc. |
|---|---|
| Theoretical Spreading Rate | The practical spreading rate depends on surface preparation, ambient environment, application method and other factors. |
| Temperature resistance | Non-continuous: 650°CContinuous: 540°C |
| Heat resistance temperature | Non-continuous temperature resistance: 650 °C, continuous temperature resistance: 540 °C |
| Application Temperature | 5°C-40°C |
|---|---|
| Mixing | Combine Base with Hardener, mix thoroughly with power agitator |
| Mixing | Mix the base and curing agent and stir thoroughly with a power tool |
| Mixing Ratio | Base/Hardener=19/1(by weight) |
| Mixing ratio | Base : curing agent = 19:1 (by weight) |
| Pot Life | 10°C | 20°C | 30°C |
| Pot life | 14hrs | 12hrs | 8hrs |
| Application Methods | Airless spray, air spray, brush and roller |
|---|---|
| Application Methods | Airless spray, air spray, brush, roller |
| Nozzle tip | Nozzle size | No. 163-415~621 |
| Nozzle pressure | Output pressure | ≥10Mpa |
| Thinning ratio | 0–5% by weight |
Brush and roller
| Thinner | Paint Thinner X |
|---|---|
| Thinner | Dedicated thinner X |
| Drying time & | Temperature | 10°C | 20°C | 30°C | |
| Overcoating interval | Surface dry | Touch dry | 3hrs | 2hrs | |
| Drying time & recoat interval | Touch dry | Semi-hard dry | 16hrs | 6hrs | |
| Min. interval | Minimum recoat interval | 24hrs | 6hrs | ||
| Max. interval | Maximum recoat interval | 7days | |||
Drying time may vary depending on film thickness,ventilation,humidity,undercoat paint condition etc.
| Applied Substrate | Bare steel |
|---|---|
| Suitable substrates | Bare steel |
| Typical topcoat | THERMOTECT WR or according to the coating system of Cosco Kansai. |
| Suitable for overcoating | THERMOTECT WR or refer to our coating system |
Store in dry, cool condition and away from sources of heat and ignition. Containers
must be kept tightly closed. Store condition shall be in accordance with national regulations
| Shelf life | Base:12 months ,Hardener: 6 months from date of production (25°C) |
|---|---|
| Shelf life | From date of manufacture, main component 12 months, hardener 6 months (25 °C) |
The information given on this sheet is to the best of our knowledge and accurate at
the time of issuing. Since conditions of use are beyond the manufacturer’s control, information contained herein is without warranty, implied or otherwise, and the suitability of the material for the use contemplated is the sole responsibility of the buyer. The information contained on this data sheet is subject to modification at any time due to our policy of modification and product development.Please check this date sheet is current prior to using the product.
The information provided in this data sheet is, to the best of our knowledge, the most complete and accurate information currently available. As the conditions of product use are beyond our control, this information carries no warranty, and we are responsible to the buyer only in the selection of the product. As our products and production processes are continuously developed, the content of this data sheet is subject to change at any time, and all information herein is subject to our confirmation. Confirm that the data sheet in hand is the latest version before using the product.
| Issued Date | 2024/07 |
|---|
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
