Iron Oxide Red Multi-purpose Primer C53-41 is a primer. Suitable for use as an anti-corrosive paint on above-waterline areas of ships and onshore steel structures; can be used with various topcoats such as alkyd, phenolic, chlorinated rubber and epoxy. Composed of alkyd resin, modified resin, anti-corrosive pigments, colouring pigments, extender pigments, additives and solvents. Can be used with various topcoats such as alkyd, phenolic, chlorinated rubber and epoxy. Parameters on this page: volume solids 50 ± 3%, dry film thickness 30 µm, theoretical spreading rate 92 g/m².
Parameter source: KAILIN original technical data sheet (TDS) for Iron Oxide Red Multi-purpose Primer C53-41; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 50 ± 3% |
|---|---|
| Dry Film Thickness | 30µm |
| Theoretical Spreading Rate | 92 g/m² |
| VOC | — |
| Density / Specific Gravity | — |
| Number of Components | — |
| Flash Point | 27°C |
| Thinner | Thinner 101 |
| Colour / Appearance | Iron red |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
| Composition | Composed of alkyd resin, modified resin, anti-corrosive pigments, colouring pigments, extender pigments, additives and solvents. |
|---|
Can be used with various topcoats such as alkyd, phenolic, chlorinated rubber and epoxy.
Suitable for use as an anti-corrosive paint on above-waterline areas of ships and onshore steel structures; can be used with alkyd, phenolic
aldehyde, chlorinated rubber, epoxy and other topcoats.
| Colour | Iron red |
|---|
| Volume Solids | 50 ± 3% (determined as specified in GB/T9272 eqv ISO3233:1998) |
|---|---|
| Dry Film Thickness | 30µm |
| Wet Film Thickness | 60µm |
| Theoretical quantity | 92g/m² |
| Flash Point | 27°C |
| Drying time (25 °C) | Touch dry ≤2 h; hard dry ≤24 h |
| Recoat interval | |||
| Temperature | 5°C | 20°C | 30°C |
| Minimum | 48h | 24h | 20h |
| Maximum | Unlimited |
|---|---|
| Recommended number of coats | 1–2 coats, dry film thickness 30–60 µm |
Can be applied directly with various topcoats such as alkyd, phenolic, chlorinated rubber and epoxy.
If 842 Epoxy MIO Anti-corrosive Paint is used as an intermediate tie coat and then applied with chlorinated rubber, epoxy, polyurethane
ester and other topcoats containing strong solvents, the compatibility is better.
Mill-scale-free steel: abrasive blast clean to Sa 2.5, or grind with pneumatic or power abrasive discs to St 3
Steel with old paint film: damaged areas and rusted areas shall be subjected to secondary derusting and ground to
St3 grade. Intact paint film areas shall be freed from all oil and contaminants on the paint film.
| Airless Spray | |
| Thinner | Thinner 101 |
| Thinning quantity | 0–5% (by paint weight) |
| Nozzle tip size | 0.4-0.5mm |
| Spray output pressure | 12–15 MPa (approximately 120–150 kg/cm²) |
| Air Spray | |
| Thinner | Thinner 101 |
| Thinning quantity | 0–5% (by paint weight) |
| Nozzle tip size | 2.0-3.0mm |
| Spray output pressure | 0.3–0.5 MPa (approximately 3–5 kg/cm²) |
| Brush/roller | Thinner 101; thinning quantity 0–3% (by paint weight) |
|---|---|
| Cleaning solvent | Thinner 101 |
| Safety measures | See the Safety Data Sheet (MSDS) of Shanghai Kailin Paint Factory. |
| Packaging | 22 kg in a 20 L drum |
| Shelf Life | 12 months |
| Note | When applying this paint, the dry film thickness shall not exceed 80 µm. |
| Notes | To use this product correctly, read the Application Guide in this data sheet carefully. |
The above information and data for this product are accumulated from our tests and practical experience
accumulated, and may serve as an application guide. For application carried out under conditions unknown to us, we
We guarantee only the quality of the paint itself and accept no responsibility for other matters. We
and reserve the right to make modifications as the product is improved.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
