Hardtop M WF Waterborne Polyurethane Intermediate/Topcoat is a waterborne coating used as an intermediate coat. Industrial protective coatings: recommended for steel structures and various equipment, including but not limited to engines, machinery, railway passenger cars and special vehicles. It can be used as an efficient intermediate coat in a complete waterborne system to provide an excellent appearance. Parameters on this page: volume solids 51 ± 2%, dry film thickness 40-70 µm, theoretical spreading rate 11.6-6.5 m²/L. Comparable models from the same brand: Hardtop XP II WB aliphatic acrylic polyurethane coating, Hardtop Clear WF waterborne polyurethane clearcoat, Hardtop E99 WF HG waterborne polyurethane high-gloss topcoat HG.
Parameter source: JOTUN original technical data sheet (TDS) for Hardtop M WF Waterborne Polyurethane Intermediate/Topcoat; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 51 ± 2% |
|---|---|
| Dry Film Thickness | 40-70 µm |
| Theoretical Spreading Rate | 11.6-6.5 m²/L |
| VOC | 139 g/L (China) |
| Density / Specific Gravity | 1.3 kg/L |
| Number of Components | Two-component |
| Flash Point | 101 °C |
| Thinner | Deionised water |
| Mixing Ratio | 5.8 parts : 1 part (by volume) |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Hardtop M WF
It is a waterborne two-component chemically curing aliphatic acrylic polyurethane coating. It has good chemical resistance. It has good application properties and is not prone to dry spray. It can be used as an efficient intermediate coat in a complete waterborne system to provide an excellent appearance. It can be used as a topcoat in a complete waterborne system with recommended Jotun waterborne primers.
Industrial protective coatings:
Recommended for steel structures and various equipment, including but not limited to engines, machinery, railway coaches and special vehicles.
Others
According to the colour chart
| Property | Test / Standard | Description |
| Volume Solids | ISO 3233 | 51± 2 % |
| Gloss (GU 60°) | ISO 2813 | Matt (0–35) |
| Flash Point | ISO 3679 Method 1 | 101 °C |
| Density | Theoretical Value | 1.3 kg/L |
| Region | Regulations | Test / Standard | VOC Value |
| China | GB 30981-2020 Limit of harmful substances of industrial protective coatings | GB/T 23985-2009 8.4 | 139 g/L |
The data listed are based on factory batch production and may vary slightly with colour.
| Gloss description | According to JOTUN's definition of functional coatings |
|---|
Typical recommended specification range
| Dry Film Thickness | 40-70 µm |
| Wet Film Thickness | 90-160 µm |
| Theoretical Spreading Rate | 11.6-6.5 m²/L |
Bright colours may require a higher dry film thickness within the recommended range to achieve hiding.
Surface Preparation
| Substrate | Minimum | Recommended |
| Coated surface | A clean, dry and sound compatible primer. | |
This product may be applied by the following methods
| Spray: | Use air spray. |
| Brush: | Recommended for touch-up and small-area application. Take care to achieve the specified dry film thickness. |
| Roller: | Use a suitable roller. With roller application, take care to apply sufficient material to achieve the specified dry film thickness. |
| Hardtop M WF Comp A — Water-Borne Polyurethane Intermediate Coat/Topcoat | 5.8 parts |
| Hardtop M WF Comp B | 1 part |
| Thinner | Deionised water |
|---|
Metal ions in tap water may cause early anti-corrosion failure.
If thinning is required, up to 25% water can be added; the thinning ratio differs for different colours. This should be done after mixing the two components.
| Nozzle tip size: | 1.5-2.5 |
| Nozzle pressure (minimum): | 2.1 bar/30 psi |
| Substrate Temperature | 10 °C | 23 °C | 35 °C |
| Touch Dry | 1.5 h | 40 min | 20 min |
| Walk-on Dry | 12 h | 7 h | 2 h |
| Minimum recoat interval | 12 h | 7 h | 2 h |
For the maximum recoat interval, refer to the Application Guide (AG) for this product.
Drying and curing times are based on the stated film thickness range, measured in a controlled laboratory environment at below 70% relative humidity.
After flash-off, the product may be force-dried at temperatures up to 60 °C.
| Walk-on Dry | 1 h |
|---|
Minimum flash-off time at the substrate temperature.
10 °C: 1 h
23 °C: 45 min
35 °C: 30 min
The minimum flash-off time is the minimum waiting time before force drying to allow moisture to evaporate.
| Touch Dry | The state at which light finger pressure leaves no mark or stickiness. |
|---|---|
| Walk-on Dry | The minimum time after which the coating allows normal foot traffic without leaving permanent footprints, marks or other physical damage. |
Minimum recoat interval after drying: the recommended minimum interval before applying the next coat.
| Paint temperature | 10 °C | 23 °C | 35 °C |
| Pot Life | 3 h | 2 h | 80 min |
Temperature
| Continuous | Peak | |
| Drying, atmospheric | 120°C | 140 °C |
Withstands peak temperatures for a maximum of one hour.
At the above temperatures, protective performance is unaffected, but appearance may be affected.
Depending on the actual exposure conditions in service, this product may be used with various primers and topcoats. Some reference systems are listed below. For specific systems, contact JOTUN.
| Previous Coat | Epoxy |
|---|
Preparation and cleaning of application equipment. To avoid contamination of water-borne paint by solvent, spray equipment must be cleaned before use. All equipment containing solvent, such as pumps, lines and guns, must be thoroughly cleaned in accordance with the following instructions.
If the application equipment is stainless steel, designed for and used only with water-borne coatings, this preparation and cleaning procedure is not required.
Before spraying:
Flush equipment and lines with JOTUN Thinner No. 17, then with Thinner No. 4, and finally with fresh water.
After spraying:
Clean equipment and lines with water and an alkaline degreaser, then flush with JOTUN Thinner No. 4, and finally with JOTUN Thinner No. 17.
| Volume | Container Size | |
| (L) | ||
| Hardtop M WF Comp A — Water-Borne Polyurethane Intermediate Coat/Topcoat | 13.6 | 20 |
| Hardtop M WF Comp B | 2.4 | 3 |
The packaging sizes above are typical reference sizes for factory batch production. Due to regional regulatory differences, packaging sizes and capacities may vary by region.
Store in accordance with national regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
Protect from frost during transport and storage.
Recommended storage temperature 5 °C to 35 °C.
| Hardtop M WF Comp A — Water-Borne Polyurethane Intermediate Coat/Topcoat | 12 months |
| Hardtop M WF Comp B | 12 months |
In some markets, the stated shelf life may be shortened to comply with local legal requirements. The above is the minimum shelf life; thereafter, testing is required to confirm quality remains acceptable.
For professional use only. Applicators and workers must be trained, experienced, capable and equipped to mix, stir and apply the coating correctly in accordance with JOTUN's technical documents. Applicators and workers must wear appropriate personal protective equipment when using this product. This guidance is provided based on current product knowledge. Any proposed modification to suit site conditions must be approved by the responsible JOTUN representative before use.
Read the safety warnings on the container packaging. Use in well-ventilated conditions. Avoid inhaling spray mist and avoid skin contact. In case of accidental splashes on skin, wash immediately with a suitable cleaner, soap and water. In case of eye contact, rinse thoroughly with water and seek medical attention immediately.
When used primarily as a primer or antifouling coating, products may show slight colour variation from batch to batch. Such products, and epoxy products used as topcoats, may chalk when exposed to sunlight.
Gloss and colour retention of topcoats depend on the colour type, the surrounding environment such as temperature and UV intensity, application quality and product type. Contact your local JOTUN office for further information.
The information in this datasheet is based entirely on knowledge gained in our laboratory and in practice. JOTUN products are regarded as semi-finished products, and their use is generally beyond our control. JOTUN therefore guarantees only the quality of the product itself. To comply with local regulations, the product may be adjusted, and we reserve the right to modify the datasheet without further notice.
Users should consult JOTUN for specific guidance on the suitability of the product for their requirements and applications.
In case of any discrepancy between language versions, the English (UK) version shall prevail.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
