A high-performance coating system for fuel oil tanks, fuel oil supply tanks, chemical storage and change tanks, ballast tanks and the well deck tops of landing craft air cushion vessels. A light-coloured, solvent-free, tar-free, two-component epoxy phenolic cargo oil tank coating. Parameters on this page: volume solids 95% ± 2%, dry film thickness 150 µm, theoretical spreading rate 6.3 m²/L. Comparable models from the same brand: International - GTA004, Interbond 201 - Low Temperature epoxy primer/topcoat, Intercryl 559 smooth washable topcoat.
Parameter source: INTERNATIONAL original technical data sheet (TDS) for Interline 624 Two-Component Epoxy Phenolic Cargo Oil Tank Coating; spreading rate and other values are converted from TDS parameters and provided for product selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 95% ± 2% |
|---|---|
| Dry Film Thickness | 150 µm |
| Theoretical Spreading Rate | 6.3 m²/L |
| VOC | 98 g/L (as supplied) (EPA Method 24). Volatile organic compound values are… |
| Density / Specific Gravity | — |
| Number of Components | Two-component |
| Mixing Ratio | Component A : Component B = 4:1 (by volume) |
| Colour / Appearance | THA626 - light yellow primer, THA625 - grey topcoat, THA623… |
| Gloss |
The manufacturer's datasheet for this model does not state the coating position or resin type, so it has not been assigned to the above categories. Browse similar products by category, orContact Usconfirm the coating system.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A light-coloured, solvent-free, tar-free, two-component epoxy phenolic cargo oil tank coating.
A high-performance coating system for fuel oil tanks, fuel oil supply tanks, chemical storage and change tanks, ballast tanks and the well deck tops of landing craft air cushion vessels. The optically active pigment (OAP) contained in the light yellow primer (THA626) assists inspection during application.
For newbuilding or maintenance and repair.
| Colour | THA626 - light yellow primer, THA625 - grey topcoat, THA623 - white topcoat |
|---|---|
| Topcoat/gloss | Gloss |
| Component B (curing agent) | THA627 |
| Volume Solids | 95% ±2% (ISO 3233:1998) |
| Mixing ratio | Component A : Component B = 4:1 (by volume) |
| Standard film thickness | Primer - 150 µm dry film thickness (158 µm wet film thickness); topcoat - 250 µm dry film thickness (263 µm wet film thickness) |
| Theoretical Spreading Rate | Primer - 6.3 m²/L at 150 µm dry film thickness; topcoat - 3.8 m²/L at 250 µm dry film thickness, allowing an appropriate loss factor |
| Application Methods | Plural-feed airless spray, airless spray, brush, roller |
| Flash Point | Component A 83 °C; Component B 110 °C; mixed 83 °C |
| Induction Time | Not required |
| Drying data | 10°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 18 h | 5 h | 3 h |
| Hard dry [ISO 9117-1:2009] | 40 h | 16 h | 6 h |
| Pot life after mixing | 50 min | 30 min | 15 min |
| Note | The mixed application time at 10 °C is for information only. The paint temperature before mixing for application is recommended to be at least 25 °C. Also refer to the mixing information on page 2. |
|---|
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||
| 10°C | 25°C | 35°C | ||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Interline 624 | 40 h | 21 days | 18 h | 21 days | 8 h | 21 days |
| Interline 624 | 40 h | 7 days | 18 h | 7 days | 8 h | 7 days |
Other
| Note | The first row of recoating data above refers to the case where the underlying coating is not exposed to UV during curing, and the second row refers to the case where the underlying coating has been exposed to UV during curing. |
|---|
| Volatile Organic Compounds | 98 g/L (as supplied) (EPA Method 24). Volatile organic compound values are typical values, provided for reference only. They may vary with factors such as colour and normal manufacturing tolerances. |
|---|---|
| Military specification | MIL-PRF-23236C, Type VII, Class 5, 7, 13 & 19, Grade C |
For the paint system best suited to the surface to be protected, consult your local International Paint representative.
For cargo oil tanks, refer to the Interline 624 cargo oil tank application procedure.
For ballast tanks, refer to the Interline 624 ballast tank application procedure.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free of contaminants.
Wash with high-pressure or ordinary fresh water as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with the SSPC-SP1 solvent cleaning standard.
Newbuilding/major repair: abrasive blast clean to Sa 2.5 (ISO 8501-1:2007). If oxidation occurs between blasting and application of Interline 624, the surface should be re-blasted to the specified pictorial standard.
Surface defects exposed by abrasive blasting must be ground, filled or treated by a suitable method.
Where required, remove weld spatter and grind welds and sharp edges smooth.
Welds and damaged areas shall be blast-cleaned to Sa2.5 (ISO 8501-1:2007) or power-tool cleaned to Pt3 (JSRA SPSS:1984).
For all shop primers, the surface should be blast cleaned to Sa 2.5 (ISO 8501-1:2007).
A sharp, angular surface profile of 50–100 µm is recommended.
For maintenance, consult International Paint.
Note: for marine environments in North America, the following surface preparation standards may be used: SSPC-SP10 instead of Sa 2.5 (ISO 8501-1:2007); SSPC-SP11 instead of Pt3 (JSRA SPSS:1984). Product mixing before application. Single-feed paint is supplied in two containers as a set. Always mix whole sets in the supplied ratio. Once a set is mixed, it must be used within the specified mixed application time.
(1) Before mixing, the temperature of Components A and B should be 20-25 °C. Excessively high component temperatures will shorten the mixed application time. If the temperature of the two components exceeds 30 °C, plural-component airless spray equipment is recommended.
(2) Stir the base (Component A) with a power mixer.
(3) Stir the curing agent (Component B) with a power mixer.
(4) Mix all of the curing agent (Component B) with the base (Component A) and stir thoroughly with a power mixer.
(5) Use quickly within the specified mixed application time.
Plural-feed: (1) Before application, do not mix the base (Component A) and curing agent (Component B).
(2) The base (Component A) should be circulated through the airless spray unit and heated to 30-40 °C by an in-line heater.
(3) The curing agent (Component B) should be kept at at least 20 °C.
Welding or flame cutting on metal coated with Interline 624: if welding or flame cutting is carried out on metal coated with this product, dust and fumes will be emitted, requiring suitable personal protective equipment and local exhaust ventilation. In North America, operate in accordance with ANSI/ASC Z49.1 "Safety in Welding and Cutting".
For mixing information, see page 2.
Do not thin.
Ensure the spray gun rate exceeds the maximum fluid output pressure of the pump in use.
Single-feed - nozzle size 0.013 in-0.019 in (330-483 µm). Smaller nozzles provide better control of primer film thickness.
- Total fluid pressure at the nozzle not less than 5000 lb/in² (352 kg/cm²). - Minimum pump ratio 70:1. It is recommended to install an in-line heater as close as possible to the fluid outlet of the pump. This allows the operator to use heat to improve the flow of the coating through long paint hoses. To achieve a paint temperature of 28-32 °C at the spray gun, a heater should be installed. The heater in the line must not be installed too high.
The recommended hose length should be as short as possible and not exceed 150 ft (46 m). A 3/8 in (9.5 mm) inner diameter paint hose and a 1/4 in (6.4 mm) inner diameter end whip achieve ideal results.
Plural-feed - total fluid pressure at the nozzle not less than 3500 lb/in² (246 kg/cm²). - The base (Component A) should be recirculated through the spray unit and heated to 30-40 °C by an in-line heater. - The curing agent should be kept at at least 20 °C.
- Nozzle size 0.013 in-0.019 in (330-483 µm). Smaller nozzles provide better control of primer film thickness.
- The mixed paint line should be kept as short as possible. When using plural-component spray equipment, it is important to ensure an adequate supply of each component to the main metering unit. If feed pumps are used, they should be carefully installed to maintain a normal supply of Components A/B and prevent cavitation in the feed hoses. Otherwise, incorrect mixing ratios may result, leading to slow curing, cracking, micro-cracking and adverse effects on mechanical properties.
Conventional spray application is not recommended.
Brush application is recommended for small areas only.
Roller application is recommended for small areas only.
International GTA822/GTA415
Do not let coating remain in hoses, spray guns or spray equipment. Flush all equipment thoroughly with International GTA822/GTA415. Once a set of paint is mixed, it should not be resealed; if the interruption during application is too long, remix the components before resuming application.
All equipment should be cleaned with International GTA822/GTA415 immediately after use. Periodically flushing spray equipment during the working day is good practice. The number of cleanings depends on spray volume, temperature and usage time (including idle time). Do not exceed the mixed application time of the coating.
All surplus paint and empty containers must be disposed of in accordance with appropriate local regulations/laws.
For plural-component application, it is important to flush the static mixer in the line, the paint mixing hose and the spray gun when work is interrupted for more than 10 minutes.
For welding information, see page 2.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; other regions — contact the regional office
At ambient temperatures below 25 °C, the gun feed line must be insulated.
The product does not cure adequately below 10 °C.
Drying times and overcoating intervals may vary with site factors such as tank geometry and ventilation rate.
For the interval required between completion of coating and ballasting, consult an International Paint representative.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. Unless otherwise specified, for ideal application performance, raise the paint temperature to between 20-25 °C before mixing and application. Unmixed paint (in tightly closed containers) should be stored protectively in the manner specified in the "Storage" section of the product data sheet. The technical and application data mentioned here are intended to form a general procedure for developing a coating application process. Test performance results come from a controlled laboratory environment; International Paint does not claim that the published test results, or any other tests, accurately represent results obtained in all field environments. Because application, environmental and design parameters vary greatly, great care should be exercised in coating selection, performance verification or use.
| Packaging Specifications | Component A | Component B | ||
| Volume | Packaging | Volume | Packaging | |
| 5 US gal | 4 US gal | 5 US gal | 1 US gal | |
For other packaging sizes, consult International Paint.
| Packaging Specifications | Packaging weight |
|---|---|
| 5 US gal | 60 lb |
| Shelf life | Component A - minimum 18 months at 25 °C or below. Long-term storage at temperatures above 25 °C will result in poor spray performance. |
|---|
Component B - minimum 18 months at 25 °C
Please consult INTERNATIONAL.
The information given in this product data sheet is not exhaustive. Anyone who uses, for any reason, any product other than those specifically recommended in this data sheet without first obtaining our written confirmation does so at their own risk as regards the suitability of the product for the intended purpose. Although we make every effort to ensure that all advice we give about the product (whether in this data sheet or otherwise) is correct, we cannot control the quality or condition of the substrate, nor the many factors affecting the application and use of this product. Accordingly, unless we specifically agree otherwise in writing, we accept no liability, to the maximum extent permitted by law, for any product performance problem arising, or for any loss or damage caused by use of the product. We therefore disclaim all warranties, express or implied, arising by operation of law or otherwise, including but not limited to any implied warranty of merchantability or fitness for a particular purpose. All products supplied and all technical guidance provided are subject to our terms and conditions of sale. You should obtain a copy of this document and read it carefully. The information contained in this product data sheet may be amended at any time in the light of experience and of our continuing product development policy. Before using the product, it is the user's responsibility to check with the local representative that the data sheet in their possession is the latest version.
This technical data sheet is also available on our websites www.international-marine.com and www.international-pc.com, and should be consistent with this document. If there is any discrepancy between this document and the version of the technical data sheet on the website, the version on the website shall prevail.
© AkzoNobel, 2016www.international-marine.com
Data is subject to the manufacturer's latest version; in all cases the manufacturer's latest TDS prevails.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
