Intergard 5755WB Waterborne Primer is a waterborne coating used as a primer. Suitable for exterior decks and superstructures, and internal areas such as machinery spaces and accommodation, for newbuildings. Provides corrosion protection as a primer, suitable for some above-water and internal areas. Parameters on this page: volume solids 51% ± 2%, dry film thickness 100 µm, theoretical spreading rate 5.1 m²/L. Comparable products from the same brand: Interbond 201 – Temperate Epoxy Primer, Interbond 808 Epoxy Anticorrosive, Intergard 5101 Universal Epoxy Primer.
Source: International original technical data sheet (TDS) "Intergard 5755WB Waterborne Primer"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 51% ± 2% |
|---|---|
| Dry Film Thickness | 100 µm |
| Theoretical Spreading Rate | 5.1 m²/L |
| VOC | 65 g/L, calculated value. VOC values are typical values provided for reference only.… |
| Density / Specific Gravity | 1.34 |
| Number of Components | Two-component |
| Mixing Ratio | Component A : Component B = 5.0:1.0 (by volume) |
| Colour / Appearance | WOB000 white, WOF684 sea grey |
| Gloss | N/A |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
A two-component waterborne epoxy primer. Provides corrosion protection as a primer, suitable for some above-water and internal areas.
Suitable for exterior decks and superstructures, and internal areas such as machinery spaces and accommodation, for newbuildings.
| Colour | WOB000 white, WOF684 sea grey |
|---|---|
| Topcoat/gloss | N/A |
| Component B (curing agent) | WOA575 |
| Volume Solids | 51% ±2% (ISO 3233:1998) |
| density | 1.34 |
| Mixing ratio | Component A : Component B = 5.0:1.0 (by volume) |
| Standard film thickness | 100 µm dry film (196 µm wet film). A dry film range of 100–125 µm (196–245 µm wet film) may be specified, depending on the end use. |
| Theoretical Spreading Rate | At 100 µm dry film thickness, theoretical spreading rate is 5.1 m²/L, allowing an appropriate loss factor |
| Application Methods | Airless spray, brush, roller |
| Flash Point | Component A >101 °C; Component B >101 °C; after mixing >101 °C |
| Drying data | 5°C | 10°C | 25°C | 35°C |
| Touch dry [ISO 9117/3:2010] | 4 h | 3 h | 2 h | |
| Hard dry [ISO 9117-1:2009] | 9 h | 8 h | 6 h | 5 h |
| Pot life after mixing | 5 h | 4 h | 3 h | 90 min |
| Recoat data — see the “Limitations” section | Substrate Temperature | |||||||
| 5°C | 10°C | 25°C | 35°C | |||||
| When recoating the following products | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum | Minimum | Maximum |
| Intergard 5755WB | 9 h | Unlimited | 8 h | Unlimited | 6 h | Unlimited | 5 h | Unlimited |
| Intergard 740 | 24 h | Unlimited | 24 h | Unlimited | 24 h | Unlimited | 24 h | Unlimited |
| Interthane 989 | 24 h | 14 days | 24 h | 14 days | 24 h | 14 days | 24 h | 14 days |
| Volatile Organic Compounds | 65 g/L, calculated value. VOC values are typical values provided for reference only. They may vary with factors such as colour and normal manufacturing tolerances. |
|---|
When used as part of an approved scheme, this coating holds the following certificate: fire resistance – complies with the Marine Equipment Directive. For details, consult your local representative.
Applied in accordance with the standard Worldwide Marine Specifications.
All surfaces to be coated must be clean, dry and free from contaminants. Wash with high-pressure or ordinary fresh water, as appropriate, and remove all oil, grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
On newbuildings, remove weld spatter and grind welds and sharp edges smooth where required.
Welds and damaged shop primer areas shall be fully blast cleaned to Sa 2½ (ISO 8501-1:2007) or power-tool cleaned to at least St2 (ISO 8501-1:2007).
Intact, approved shop primer must be clean, dry and free of soluble salts and any other surface contaminants.
Unapproved shop primer must be blast cleaned to Sa 2½ (ISO 8501-1:2007).
For specific advice, consult your local representative.
Note: for marine environments in North America, the following surface preparation standards may be used: SSPC-SP10 instead of Sa 2.5 (ISO 8501-1:2007); SSPC-SP2 instead of St2 (ISO 8501-1:2007).
The coating is supplied in two containers as one unit. Always mix the entire unit in the supplied ratio.
(1) Stir the base (Component A) with a power mixer.
(2) Mix all of the curing agent (Component B) with the base (Component A) and stir thoroughly with a power mixer.
Not recommended. Use clean water as thinner only in special circumstances (maximum 3% by volume).
Recommended nozzle size 0.38–0.53 mm (15–21 thou); total output fluid pressure at the nozzle not less than 176 kg/cm² (2500 psi)
Conventional spray application is not recommended.
Brush application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
Roller application is recommended for small areas only. Several coats may be required to achieve the specified film thickness.
International GTA822/water
Do not allow coating to remain in hoses, spray guns or spray equipment. Flush all equipment thoroughly with International GTA822/water. Once a kit of paint has been mixed, it should not be re-sealed. If the interruption in application is too long, it is recommended to mix fresh components before resuming.
Clean all equipment immediately after use with International GTA822/water. Periodic flushing of spray equipment during the working day is good practice. The number of flushings depends on the quantity sprayed, temperature, relative humidity and time used (including delays). Do not exceed the pot life of the coating.
All surplus paint and empty containers must be disposed of in accordance with appropriate local regulations/laws.
If welding or flame cutting is performed on metal coated with this product, dust and fumes will be released; use suitable personal protective equipment and local exhaust ventilation. In North America, follow the instructions in ANSI/ASC Z49.1 “Safety in Welding and Cutting”.
All work related to the application and use of this product must comply with national health, safety and environmental protection standards and regulations.
Before using this product, obtain, read and follow the health and safety information in the Material Safety Data Sheet for the product. Read and observe all precautions in the Material Safety Data Sheet and on the container label. If these warnings and requirements are not fully understood, or cannot be strictly observed, do not use the product. During application and drying of the product, provide adequate ventilation and protective measures to keep solvent vapour concentrations within safe limits, so as to prevent poisoning or oxygen deficiency. Take protective measures to avoid skin and eye contact with the product (e.g. gloves, goggles, face shield, barrier cream). Specific safety measures depend on the application method and working environment.
Emergency contact: USA/Canada — medical 1-800-854-6813; Europe — tel. (44) 191 4696111, hospital and doctor (44) 207 6359191; other regions — contact the regional office
Must meet the following parameters: Intergard 5755WB shall always be protected from freezing during storage and transport. Recommended storage temperature 25 °C.
Recoat data are for guidance only and depend on local climatic and environmental conditions. For specific advice, consult your local International Paint representative.
Apply in good weather. The temperature of the surface to be coated must be at least 3 °C above the dew point. For ideal application performance, raise the paint temperature to between 21 and 27 °C before mixing and application. Ensure humidity is below 80%, otherwise drying and recoat times will be severely extended. Unmixed paint (in tightly closed containers) shall be protectively stored as specified in the "Storage" section of this product datasheet. The purpose of the technical and application data mentioned here is to establish a general procedure for a coating application programme. Test performance results come from controlled laboratory environments; International Paint does not claim that the published test results, or any other tests, precisely represent results obtained in all site environments. Because application, environmental and design parameters vary widely, great care should be exercised in coating selection, performance verification and use.
| Packaging Specifications | Component A | Component B | ||
| Volume | Packaging | Volume | Packaging | |
| 15 L | 12.5 L | 18 L | 2.5 L | 3 |
For other packaging sizes, consult International Paint.
| Packaging Specifications | Packaging weight |
|---|---|
| 15 L | 21.49 kg |
| Shelf life | At 25 °C, minimum 12 months. Thereafter, re-inspection is required. Store in a dry, sheltered place away from heat and sources of ignition. |
|---|
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
