HEMPEL Silicone Epoxy Sealer 27100 is an epoxy coating. This product is used for repair and maintenance of damaged areas of existing silicone topcoats to ensure the anticorrosive primer is compatible with HEMPEL Silicone Repair Coating 27500 or HEMPEL Silicone Fouling Release Sealer 27700. HEMPEL Silicone Epoxy Sealer 27100 is a two-component epoxy primer with anticorrosive properties. Parameters on this page: volume solids 53 ± 2%, dry film thickness 125 µm, theoretical spreading rate 4.2 m²/L. Comparable products from the same brand: HEMPEL Solvent-free Phenolic Epoxy Lining 430, HEMPEL Solvent-free Phenolic Epoxy Lining 630, HEMPEL Silicone Fouling Release Sealer 27400.
Parameter source: HEMPEL original technical data sheet (TDS) 'HEMPEL Silicone Epoxy Sealer 27100'; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 53 ± 2% |
|---|---|
| Dry Film Thickness | 125 µm |
| Theoretical Spreading Rate | 4.2 m²/L |
| VOC | 409 g/L (China) |
| Density / Specific Gravity | 1.4 kg/L |
| Number of Components | Two-component |
| Flash Point | 22°C |
| Colour / Appearance | Light brown-red 55900 |
| Gloss | Flat |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
HEMPEL Silicone Epoxy Sealer 27100 is a two-component epoxy primer with anticorrosive properties.
HEMPEL Silicone Epoxy Sealer 27100 is a tie coat between an anticorrosive primer and silicone/silicone foul-release coatings.
The product is used for patching and repair of damaged areas of existing silicone topcoats to ensure compatibility between the anticorrosive primer and HEMPEL Silicone Repair Coating 27500 or HEMPEL Silicone Foul-release Sealer 27700
Good adhesion
| Product safety | Flash point 22 °C |
|---|
| Regulations | Value |
| European Union | 409 g/L |
| USA (coatings) | 409 g/L |
| USA (regulatory) | 409 g/L |
| China | 409 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 27100 |
|---|---|
| Product components | Base 27109 |
Curing Agent 98162
| Standard colour / code | Light brown-red 55900 |
|---|---|
| Gloss | Flat |
| Volume solids | 53 ± 2% |
| density | 1.4 kg/L |
| Recommended dry film thickness | 125 µm |
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 27109 : Curing Agent 98162 (15.7 : 4.3 by volume)
For multi-component products, use a container of suitable volume. Do not open or mix the cans before use. Stir thoroughly before use. Thinning is not permitted.
Thinner
| Cleaning solvent | HEMPEL's Thinner 08450 |
|---|
| Product temperature | 20°C |
| Pot Life | 60 min |
| Pot life (spray) | 60 min |
| Pot life (brush) | 60 min |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | No thinning required | Nozzle pressure: 15 MPa; nozzle size: 0.48–0.53 mm |
| Brush | No thinning required | Not applicable. |
Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Wet Film Thickness | 188 µm | 236 µm | |
| Theoretical Spreading Rate | 5.3 m²/L | 4.2 m²/L | |
| Surface temperature | 20°C |
| Surface Dry | 90 min |
| Through dry | 6 h |
Measured at 125 µm dry film thickness under standard conditions; see Hempel's explanatory notes.
For further information, refer to Hempel's specifications.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Binder | 18 months |
| Curing agent | 18 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| GWP (Global Warming Potential) | 7.4 g CO₂e/m² |
|---|
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
