HEMPEL's Fibre-containing Inorganic Zinc-rich Paint 15750 belongs to Zinc-rich Primer. Used as a general anti-corrosive and anti-rust primer for newbuilding and repair, suitable for steel structures and piping. The product complies with SSPC paint 20 Grade 1 and the component requirements of ISO12944-5,2018, and fully complies with the requirements of ISO3549 and ASTM D520 Type II. Parameters on this page: volume solids 62 ± 2%, DFT 75 µm, theoretical spreading rate 8.3 m²/L. Comparable models from the same brand: HEMPEL's Zinc-rich Primer 16490, HEMPEL's Inorganic Zinc-rich Paint 15700, HEMPEL's Inorganic Zinc-rich Paint 15780.
Parameter source: HEMPEL original technical data sheet (TDS) "HEMPEL's Fibre-containing Inorganic Zinc-rich Paint 15750"; values such as spreading rate are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 62 ± 2% |
|---|---|
| Dry Film Thickness | 75 µm |
| Theoretical Spreading Rate | 8.3 m²/L |
| VOC | 535 g/L (China) |
| Density / Specific Gravity | 2.4 kg/L |
| Number of Components | Two-component |
| Flash Point | 14°C |
| Thinner | HEMPEL's Thinner 08700 |
| Colour / Appearance | Grey 19840 |
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
HEMPEL's Fibre-containing Inorganic Zinc-rich Paint 15750 is a solvent-borne, self-curing, fibre-reinforced inorganic zinc-rich paint with excellent weather resistance and abrasion resistance. It tolerates high film thickness. It provides cathodic protection to locally mechanically damaged areas.
The product complies with SSPC paint 20 Grade 1 and the component requirements of ISO12944-5,2018, and fully complies with the requirements of ISO3549 and ASTM D520 Type II.
Used as a general-purpose anticorrosive primer for newbuilding and repair, suitable for steel structures and pipelines. For use in various atmospheric corrosion environments (up to extreme corrosion, such as offshore).
As a single, complete long-life protective coating, applied to steel surfaces exposed to moderate to severe corrosive environments and subject to abrasion; particularly suitable for steel structures where local film thickness (for example at corners) may be excessive (DFT up to 200 µm).
- With a suitable topcoat: fully dry, atmospheric exposure: 540 °C [1004 °F], peak: 600 °C [1112 °F].
| Product safety | Flash point 14 °C |
|---|
| Regulations | Value |
| European Union | 458 g/L |
| USA (coatings) | 535 g/L |
| USA (regulatory) | 545 g/L |
| China | 535 g/L |
| Hong Kong | 545 g/L |
| South Korea | 535 g/L |
Subject to specific legislation; see the explanatory notes on the Hempel website hempel.com or your local Hempel website. This product complies with the VOC requirements of national mandatory or recommended standards; consult the company representative for details.
Handle with care. Before and during use, observe the safety labels on the packaging and paint containers and comply with all local and national safety regulations. Consult the Hempel Safety Data Sheet and Product Data Sheet for the product at all times.
For professional use only.
| Product code | 15750 |
|---|---|
| Product components | Base 15759 |
Zinc 97170
| Standard colour / code | Grey 19840 |
|---|---|
| Gloss | Flat |
| Volume solids | 62 ± 2% |
| density | 2.4 kg/L |
| Recommended dry film thickness | 75 µm |
For further details, refer to the separate Hempel document Surface Preparation Guide.
Base 15759 : Zinc 97170 (9.2 : 15 by weight)
Products containing floating or settling particles/pigments require continuous stirring during application; this is especially important when heavily thinned.
| Thinner | HEMPEL's Thinner 08700 |
|---|---|
| Cleaning solvent | HEMPEL's Thinner 08700 |
| Product temperature | 10°C | 20°C |
| Pot Life | 8 h | 4 h |
| Tools | Maximum thinning volume | Application parameters |
| Airless Spray | 30% | Nozzle pressure: 10 MPa; nozzle size: 0.48–0.58 mm |
| Air Spray | 35% | Not applicable. |
| Brush | 10% | Not applicable. |
To reduce dry spray at high temperatures, additional thinning may be required. If brush or roller application is used, several coats may be required to achieve the specified dry film thickness. Spray parameters are indicative and may be adjusted to suit site conditions. Pressure figures apply to the material at 20 °C. (*For other application methods, consult the company representative.)
| Specification range | Low | High | Recommended |
| Dry Film Thickness | 40 µm | 125 µm | 75 µm |
| Wet Film Thickness | 64 µm | 201 µm | 121 µm |
| Theoretical Spreading Rate | 16 m²/L | 5 m²/L | 8.3 m²/L |
Excessive thickness shall be strictly controlled; local DFT shall never exceed 250 µm [10 mils]. Where surfaces are irregular, particular attention is required to avoid over-application.
| Surface temperature | 0°C | 10°C | 20°C | 30°C |
| Touch Dry | 90 min | 40 | 15 | 6 |
| Fully cured | 48 h | 23 | 10 | 5 |
Determined at 75 µm DFT under standard conditions; see Hempel's explanatory notes for details. Drying time of moisture-curing products depends on relative humidity; on-site drying times may therefore vary.
- To achieve the stated drying times, adequate ventilation during application, drying and curing is essential.
| Ambient temperature | 25°C |
| Binder | 6 months |
| Zinc | 36 months |
When stored in unopened original containers, shelf life is counted from the date of production. Thereafter, the product quality must be re-inspected. Storage at high temperatures may shorten the shelf life. For advice, consult Hempel.
- Store the product in accordance with the Safety Data Sheet, label and local regulations. Keep containers in a dry, cool, well-ventilated place away from heat and sources of ignition. Keep containers tightly closed. Handle with care.
| Number | Document description | Location/Notes |
| 3. | PDS | This document |
datasheet, which is also available for download at www.hempel.com.
| Dry Film Thickness | 1 µm | |
| GWP (Global Warming Potential) | 12.1 g CO₂e/m² |
Carbon footprint is based on a 1 µm dry film thickness formed over a surface area of 1 m².
The scope includes raw materials, transport to the Hempel factory, the Hempel production process, and any volatile organic compounds (VOC) emitted during and after use of the product.
Calculated based on the standard colours defined in this PDS. Values may vary with colour.
For further information, refer to the Hempel website (https://www.hempel.com/service-and-support/technical-guidelines) or your local Hempel website:
This Product Data Sheet (“PDS”) relates to the product supplied (the “Product”), and its content is updated from time to time. Accordingly, the buyer/applicator should refer to the PDS supplied with the relevant batch of product (rather than an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the specifications, declarations and/or guides shown below, which are also available for download from the “Products” page of the Hempel website (www.hempel.com) (hereinafter the “Supplementary Documents”):
| 1. | Technical declaration | Provides one-off specific advice for the requirements of a specific project |
| 2. | Specifications | Issued for specific projects only |
| 4. | Explanatory notes to the PDS | Available for download at www.hempel.com, containing information related to product test parameters |
| 5. | Application guide | If available, provided at www.hempel.com |
| 6. | General technical guidelines (e.g. application and surface preparation) |
If the information in the PDS and the supplementary documents is inconsistent, the information shall take precedence in the order listed above. In this case, contact the Hempel representative for clarification. In addition, the buyer/applicator must give full consideration to the relevant safety information accompanying each product. Hempel accepts no liability for any defects arising from application not carried out fully in accordance with the recommendations and requirements of the relevant PDS and supplementary documents. The information and terms in this disclaimer apply to this PDS, the supplementary documents and any other relevant documents provided by Hempel for this product. In addition, unless otherwise expressly agreed in writing, supply of the product and all technical support are subject to Hempel's General Conditions of Sale, Delivery and Service.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
