8034 SILICON HR SILVER Silicone Heat-resistant Aluminium Coating is a heat-resistant coating in the silicone system. SILICON HR SILVER is a silicone heat-resistant coating composed of silicone resin and aluminium paste, applicable over inorganic zinc primers. Parameters on this page: volume solids 28 ± 2% (ISO: 3233), dry film thickness 15–20 µm, theoretical spreading rate 0.054–0.071 L/m². Comparable products from the same brand: 8033 SILICON HR Silicone Resin Heat-resistant Coating, 8033B SILICON HR BLACK Silicone Resin Heat-resistant Coating, 8032 SILICON HR PRIMER Silicone Resin Heat-resistant Primer.
Source: CMP original technical data sheet (TDS) "8034 SILICON HR SILVER Silicone Heat-resistant Aluminium Coating"; spreading rate and other values are converted from TDS parameters and are for selection reference only.
The above content is compiled from the manufacturer's datasheet and this site's parameter tables. For selection, coating systems and lead times, pleaseContact Usfor confirmation.
This page carries the full TDS for this product, translated from the manufacturer's original document. No file download is needed; for an original-language copy, send an enquiry.
| Volume Solids | 28 ± 2% (ISO: 3233) |
|---|---|
| Dry Film Thickness | 15–20 µm |
| Theoretical Spreading Rate | 0.054-0.071 L/m2 |
| VOC | 658 g/L (Method 24) |
| Density / Specific Gravity | 1.08 g/mL (ISO: 2811) |
| Number of Components | Two-component |
| Thinner | SILICON THINNER A |
| Mixing Ratio | Base : accelerator = 100:1.21 (by volume) |
| Colour / Appearance | Silver |
SILICON HR SILVER is a silicone heat-resistant coating composed of silicone resin and aluminium paste, applicable over inorganic zinc primers.
| It has the following advantages | 1. Excellent heat resistance (up to 700 °C). 2. Excellent weatherability. 3. Excellent application performance. 4. Excellent compatibility with inorganic zinc primers. |
|---|
| Type | Silicone heat-resistant aluminium coating |
|---|---|
| Use | Can be used as a primer for boilers and engine cylinders; as the topcoat of exhaust pipes, radiators, oil lamps, etc. |
| Mixing Ratio | Base : accelerator = 100:1.21 (by volume) |
|---|---|
| Colour | Silver |
| Flash Point | Base 22.3 °C, accelerator 38.3 °C |
| Density | 1.08 g/mL (ISO: 2811) |
| Volume Solids | 28 ± 2% (ISO: 3233) |
| Volatile organic compound content | 658 g/L (Method 24) |
| Theoretical spreading rate | 0.054-0.071 L/m2 |
| Wet Film Thickness | 54–71 µm |
| Dry Film Thickness | 15–20 µm |
(20 µm dry film)
| Temperature | 5 °C | 10 °C | 20 °C | 30 °C | |
| Drying Time | Surface Dry | 1 h | 50 min | 30 min | 20 min |
| Hard Dry | 7 h | 5 h | 3 h | 1 h | |
| Recoat interval | At least | 24 h | 20 h | 16 h | 10 h |
| At most | - | - | |||
| Pot life | 32 h | 28 h | 24 h | 16 h |
| Application method | Airless spray, brush |
|---|---|
| Weather: temperature | Minimum 0 °C |
| Humidity | Maximum 85% |
| Airless spray: viscosity | 10–20 s (Ford Cup #4) |
| Nozzle | Graco 415 |
| Paint output pressure | 8.8-11.8 Mpa |
| Spray gun speed | 70–100 cm/s |
| Thinner | SILICON THINNER A |
| Thinning | 0–15% by volume |
The surface to be coated must be clean; remove rust, dust, grease and other contaminants by power washing, cleaning agents or solvent wiping
| Preceding coat | SILICON HR PRIMER,GALBON S-HB |
|---|---|
| Subsequent coat | - |
| Packaging | Two-component |
Note: 1. In enclosed spaces or confined spaces at low temperature, ventilation is necessary to remove volatilised solvent during application and film formation to promote film formation.
2. Stir the base with an electric stirrer to a uniform state, then thoroughly stir all of the curing agent with the base. Finally add an appropriate amount of thinner and mix thoroughly.
3. Excessive solvent may reduce sag resistance and other film properties.
4. The film should be baked at 200 °C for 2 hours until fully hard dry.
5. The total film thickness of the paint system must not exceed 150 µm.
| 6. Base | to curing accelerator mixing ratio (by weight) is 100:1. |
|---|
7. Density, volume solids and VOC content are theoretical calculated values without thinner.
Information is subject to the manufacturer's latest version; the manufacturer's latest TDS prevails.
The technical parameters on this page are taken from the product's original manufacturer technical datasheet, the copyright of which belongs to the manufacturer. If a rights holder considers the presentation inappropriate, contact us for verification and handling.
For more Q&A on selection, application, acceptance and defect diagnosis, seeFAQsection.
Packaging specifications and batch lead times are subject to actual availability. PleaseContact Uscontact us for project-based calculation.
